Recessed concrete outdoor spotlights
This selection is also available in our French store: Spots d exterieur encastrables en béton
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right light output?
At what height should the light be installed?
What type of bulb?
Compatible with LEDs and dimmers?

Light changes everything
From statement chandeliers to discreet wall lights, we help you choose the right brightness, height and style for every room.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
First check the diameter and recess depth available in your surface, then the protection rating shown on the datasheet: these three values decide whether a concrete recessed outdoor spotlight can be installed at your home. The body sits flush with the paving, only the glass remains visible, and the light grazes across the terrace or driveway.
What is a concrete recessed outdoor spotlight?
A concrete recessed outdoor spotlight is a luminaire whose body sits flush with the surface: only the glass remains visible. It highlights a driveway, a pool edge or a planting bed without a wall-mounted projector, and is chosen on its recess format, its socket and its protection rating.
A flush luminaire, not a surface-mounted block
The concrete block sits in the slab and the glass comes level with the paving. Nothing protrudes, the lawnmower passes over, the eye catches on no housing. This discretion means you must know the dimension before pouring, since the luminaire can no longer be adjusted once the surface is laid. Recessed outdoor spotlights are therefore as much a finishing choice as a lighting one.
Terrace, driveway, pool edge: where it disappears
On a terrace, the spotlight borders the pool edge or runs along the base of the wall. In a driveway, it marks the edge of the path. Around a planting bed, it sits in the gravel or mulch. The surface dictates the choice: concrete pairs with stone, sand and light paving, and stands out more on dark asphalt. The full range can be found in the entire Designix lighting range.
How to choose a concrete recessed outdoor spotlight?
The choice comes down to four points: the recess diameter available in the surface, the type of source (socket or integrated LED), the protection rating shown on the datasheet and the fixed or adjustable beam direction. The colour of the body also matters, since it determines how discreet the spotlight is once installed.
Socket or integrated LED: what it changes for replacement
A socket takes a screw-in bulb: you choose the colour temperature and replace the source without touching the luminaire. An integrated LED cannot be replaced, but the beam is calibrated at the factory and there is no bulb to buy again. The first suits a garden you plan to change over time, the second an installation you want to keep stable. Compare the integrated LED models with the socket versions before deciding.
Protection rating and depth: the two lines to read on the datasheet
The protection rating first: as a general guide, IP65 designates a luminaire protected against dust and water jets, which covers rain and splashes from cleaning. Check it model by model, along with the presence of a gasket and proper drainage under the spotlight. The depth and drilling diameter next: they appear on the datasheet and determine the recess. For even light across a facade, also look at LED outdoor lighting.
On colour, a light body blends into sand-coloured paving, a dark body fades into asphalt. See the white finishes and the black colourways depending on your ground.
Where and how to arrange spotlights on a terrace or driveway?
Spotlights are placed where the ground changes or where people walk: driveway edge, step edge, base of wall, terrace perimeter. Better a few points well aimed at a wall, a tree or gravel than a regular alignment that draws patches on the paving.
Lighting a path without glare
The beam points at the ground, never towards the eyes of someone approaching. Two or three points are enough to read a path: marking every metre creates a runway effect. The outer edge of the driveway, on the planting side, gives softer light than placing it in the middle of the path.
Highlighting a tree, a wall or a gravel bed
An adjustable beam can be aimed after installation, once the surface is finished, to run up a trunk or graze a wall. Adjustable-beam ground spotlights save you from redoing everything if the tree grows or the planting bed changes. To widen the subject to other points in the garden, see adjustable outdoor lighting.
| Area | What you aim to light | Criterion to check first | Point of caution |
|---|---|---|---|
| Driveway and path | guide the step | beam aimed at the ground, flush model | do not protrude from the surface |
| Terrace and pool edge | grazing ambient light | fixed or adjustable direction | keep access to the luminaire |
| Planting bed and tree base | highlighting the planting | adjustable beam | distance to the planting |
| Gravel bed or mulch | discreet pools of light | stability of the body in a loose base | compaction of the base |
| Pond or pool edge | beach lighting | protection rating shown on the datasheet | check the datasheet first of all |
| Base of facade | vertical wall lighting | beam adjustable upwards | avoid shining into windows |
How to install a recessed spotlight in a slab or surface?
A recessed ground spotlight requires a recess in the slab or sand bed, a conduit for the cable and a sleeve that lets the luminaire sit flush without protruding. The depth and diameter to allow for appear in the model's technical datasheet, to be consulted before pouring.
Preparing the recess before pouring
The dimension is taken from the datasheet, then a recess slightly deeper than the luminaire body is made to house the connection. Core drilling remains possible on an existing surface, provided you reach the conduit without cutting into it. A spotlight buried under the paving, too high or too low, can only be corrected by breaking it out.
Conduit, drainage and access to the luminaire
The cable runs in conduit, the connection is made with the power off, and the area around the spotlight stays drained so water does not pool on the gasket. Always leave room to remove the glass for cleaning. When digging a trench is not possible, solar solutions without wiring and solar LED spotlights avoid the work, with the runtime specific to each model.
E27 outdoor bulb: which choice for a concrete recessed spotlight?
A spotlight with an E27 socket takes a screw-in bulb, replaceable without dismantling the luminaire. On a terrace, choose a bulb intended for outdoor use and suited to the purpose: night light, path lighting or highlighting. The accepted wattage and temperature depend on the luminaire and appear on its datasheet.
Choosing an E27 bulb intended for outdoors
An indoor bulb placed behind a spotlight glass breathes poorly: confined air, humidity and temperature swings wear out its electronics. Look for a reference rated for outdoor use, with the same colour temperature as the other points on the terrace to avoid a yellow point in the middle of a white set.
Night light, path lighting, highlighting: three uses, three bulbs
A night light needs a low, constant level, lit for a long time. Path lighting needs a crisp, brief light on the walkway. Highlighting accepts a tighter beam, aimed at a wall or planting. The figures vary from one luminaire to another: read the datasheet rather than copying a setting found elsewhere.
| Solution | What you gain | What you lose | For whom |
|---|---|---|---|
| E27 socket | replaceable bulb, colour and wattage to choose | bulb to buy and protect from humidity | a garden you plan to change over time |
| Integrated LED | nothing to change, beam calibrated at the factory | replacing the whole luminaire at end of life | an installation you want to be permanent |
| Adjustable module | beam set after installation | setting to redo after cleaning | planting beds, walls and facades |
How to wire spotlights in series or in parallel?
In series, the spotlights follow one another on the same circuit and depend on each other; in parallel, each point remains independent. The choice depends on the number of luminaires, the voltage shown on the datasheet and the possible presence of a transformer, to be confirmed with an electrician before connection.
Series or parallel: what changes if a spotlight fails
In a series setup, a faulty point can break the chain and switch off those that follow. In parallel, each spotlight receives its own feed from the supply: a fault stays local, which matters on a driveway used in the evening. Series wiring mainly concerns low-voltage installations.
Voltage, transformer and control: what to check
The supply voltage and the presence of a transformer are shown on the luminaire datasheet, not on the bulb box. If you want to lower the intensity in the evening, check compatibility with a dimmer: dimmer-compatible spotlights and LED dimming do not behave the same way depending on the modules.
What mistakes to avoid before ordering a recessed outdoor spotlight?
The costly mistakes happen before ordering: forgetting to check the recess diameter and depth, planning an inaccessible model for replacement, choosing a look without checking the protection rating, or multiplying light colours on the same facade.
The dimensions to check before ordering
- Drilling diameter and recess depth read from the datasheet.
- Surface thickness and space available for the conduit.
- Protection rating and presence of a gasket.
- Source type and accessibility for replacement.
Anticipating replacement, cleaning and maintenance
A flush spotlight is cleaned with clear water and a soft cloth; concrete ages over time without losing its mineral look. Above all, allow for access: a glass that can no longer be unscrewed turns a bulb change into a job. For a facade where the luminaire must look good by day, the design models offer more refined lines, and our lighting for home and garden completes the set.
This collection contains no products at the moment. In the meantime, browse the recessed ground spotlights or contact Designix customer service to be guided towards a model suited to your installation.
Frequently asked questions about concrete recessed outdoor spotlights
How to arrange spotlights on a ceiling?
In an interior room, recessed ceiling spotlights are placed according to the areas to be lit, not according to the furniture: worktop, circulation, table. Avoid a regular alignment placed at random and check the recommended spacing in the luminaire datasheet before drilling.
How to install recessed ceiling spotlights?
Mark the points, check there is no conduit or joist, drill to the diameter shown on the datasheet, connect with the power off and then clip the luminaire in. A sufficient recess and access to the source matter more than the speed of installation.
How many spotlights are needed in a kitchen?
The question is handled by zones rather than by number: worktop, sink, hob and circulation each have their own need. Cross the surface to be lit with the spacing shown in the datasheet of the chosen spotlight, adding under-cabinet light for worktops. See the recessed spotlights for kitchens.
How to choose an outdoor terrace wall light?
A terrace wall light is chosen on its protection rating, the material of its body and the direction of its light: downwards to light without glare, diffused to dress a facade. It complements a ground spotlight rather than replacing it.
Can a concrete recessed spotlight be installed in lawn or gravel?
Yes, provided the base remains stable and the luminaire sits flush without being covered. In gravel or lawn, allow for a compacted bed or a sleeve around the spotlight, and keep access to the luminaire for cleaning and bulb replacement.





