12V recessed pool spotlights
This selection is also available in our French store: Spots encastrables 12V pour piscine
No products in this selection.
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right product?
What are the delivery times?
Can I return an item?
Can I pay in instalments?

An interior that reflects who you are
Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
Measure the niche diameter and the wall material before choosing: these two measurements decide which recessed model you need, well before the light colour. A 12V LED pool light runs on very low voltage with a transformer placed outside the pool, and projects an underwater beam from the wall that makes the water readable in the evening.
What light does a recessed 12V pool light give?
A recessed 12V pool light projects an underwater beam that lights the wall and the water surface from inside the pool. Depending on the model, the light is warm white or cool white, and stays at very low voltage: electrical risk is limited in a damp environment and glare from the terrace is avoided.
The beam grazes the wall rather than hitting the eye. The result: water readable from the coping, reflections that trace the outline of the pool, and no blinding spot when you sit beside it. The effect is judged from outside, never from above the light.
Why choose 12V rather than 230V for a pool?
12V lowers the voltage as close as possible to the luminaire: the transformer takes the 230V and converts it, then the cable runs to the wall at very low voltage. This transformer goes outside the pool volume, in a ventilated and accessible room, because you will need to return to it for maintenance. The wiring becomes easier to secure, and the line is found in the Designix lighting catalogue like any outdoor circuit. The mains part is a job for an electrician.
Warm white or cool white: which light colour for the pool?
Around 2700 to 3000 K, warm white warms the stone and extends an evening on the terrace; between 4000 and 6000 K, cool white gives clearer water, appreciated for early swimming or for a contemporary-style pool. Look at the coping and the terrace surface before deciding, then keep the same family on the neighbouring recessed outdoor spotlights: two similar temperatures in one garden are immediately visible.
How to choose a recessed 12V pool light?
First look at the pool wall, because it dictates the niche or the housing for the light. Then come the body material, the protection rating intended for immersion, the available diameter and the cable length. Finish and light temperature are chosen last, once compatibility is established.
| Criterion | What to check | Why it matters |
|---|---|---|
| Voltage | 12V operation with a suitable transformer | Very low voltage in a damp environment |
| Protection rating | Rating intended for prolonged immersion | A surface rating is not enough underwater |
| Body material | 316L stainless steel, ABS or polypropylene depending on the environment | Resistance to salt, limescale and chlorine |
| Format | Diameter and type of niche or mounting plate | Determines fitting in the existing wall |
| Cable | Cross-section and length of the line | Limits voltage drop and weakening of the beam |
| Finish and light | Colour, warm white or cool white, orientation | Harmony with the coping and terrace |
Recessed 12V pool lights: which body materials?
316L stainless steel withstands salt water and chlorine over time; 304 stainless steel is enough for a pool with gentle treatment but marks faster with salt. ABS and polypropylene suit aggressive water and tighter budgets, provided the material is stated for immersion. Tempered glass protects the source and rinses in one wipe. A full range is shown in the LED outdoor lighting models.
What is the difference between a PAR56 niche and a small screw-in light?
The PAR56 niche is a housing built into the wall, intended for a large-format projector: it must exist or be created during casting. A small screw-in light needs only a calibrated hole or a mounting plate, often around ten centimetres in diameter, and fits on liner as well as on a rigid wall. On a pool already filled, the second avoids heavy work. Recessed adjustable spotlights also let you aim at the wall rather than the bottom.
What is the ideal cable cross-section for a 12V LED light?
The cable cross-section depends on the line length and the light power: the longer the cable, the larger the cross-section needed to avoid a voltage drop that weakens the beam. The luminaire instructions and the transformer give the value to respect, to be validated by the electrician.
In practice, a short line and a transformer close to the pool limit losses. The cable runs in conduit or sleeve from the wall to the plant room, without bare passage in the ground or the coping. The pool equipotential bonding and the mains connection are not a DIY job: they require a professional. A dimmable model adds brightness adjustment that compensates for light that is too strong in the evening.
How to install a recessed 12V light in a pool?
Installation begins with the recess in the wall and the cable run in conduit, then the connection to the 12V transformer placed outside the pool volume. The light is fixed in its niche with its gasket, and refilling waits for the watertightness check. A qualified electrician validates the electrical part.
Do you have to empty the pool to work on it?
An initial installation is done dry, before refilling, with a watertightness check on the finished wall. For a replacement, some models can be removed from the pool in place, the new gasket is fitted underwater and the work is done with the power off. This possibility depends on the model and its fixing method: check it before buying, not after.
How to run the cable without damaging the structure?
Provide a sleeve during casting or use a watertight cable gland on an existing wall, with a slope that prevents water from stagnating in the conduit. The route runs along the wall to the plant room. Allow a little slack close to the luminaire so the light can be pulled out during maintenance, then continue the same line to the entrance lighting points and to the staircase steps.
How to arrange spotlights on the ceiling and around the pool?
Around a pool, the aim is to light the walls and walkways rather than multiply points: one or two lights per long side are enough to read the water. Under a covered terrace ceiling, space them at regular intervals keeping walkways out of the direct beam.
How to arrange spotlights on a covered terrace ceiling?
Align the points on one or two parallel lines, at a constant distance from the wall, and space them at a regular pitch to avoid patches. Then aim the beams towards the use areas, table or relaxation corner, never towards the eyes of someone sitting. A narrow terrace needs only one line. The same distribution principle guides hallway spotlights indoors.
How to space the light points along the coping?
Place one at each visible end and one in the middle of the long side: the eye then reads a continuous line. Reinforce the corners and the step edge, never the swimming area. Finally keep the same colour temperature between the pool and the surroundings, so the light does not change shade going from water to stone; lighting for the home follows the same logic.
Which 12V light for an above-ground pool?
An above-ground pool has thin walls: a recessed light does not find the niche depth it needs there, unless a technical recess was provided during manufacture. You then turn to a surface projector fixed to the wall, at very low voltage, or to a submerged light placed in the pool.
| Pool type | Suitable solution | Point of vigilance |
|---|---|---|
| Concrete or masonry with niche | Recessed light in the existing niche | Niche diameter and cable length to record before purchase |
| Liner or membrane | Recessed light with a plate suited to the liner | Gasket and cable gland tightening to check |
| Above-ground pool with thin wall | Surface projector or submerged light to fix | No recess to embed without crossing the wall |
| Salt water pool | 316L stainless steel body or plastic material for immersion | Rinse the glass and check the gaskets each season |
| Fountain or decorative pool | Small submerged light at very low voltage | Immersion depth respected |
Recessed 12V lights for above-ground pools: which solutions?
The wall projector is fixed to the structure and sends light towards the bottom; it requires no cutting. The submerged light placed in the pool suits small structures and is easy to remove for winterising. In both cases, very low voltage remains the rule. Adjustable outdoor projectors complete the scene from the terrace.
Can you drill the wall of an above-ground pool?
An unplanned hole weakens the liner or panel and opens the way to a slow leak, hard to locate. If the structure was not made with a recess and reinforcement, it is better to give up recessing and choose a surface fixing. For the surround and the LED-lit steps, the question does not arise: you are out of the water.
Salt water, limescale, winterising: how to maintain a pool light?
Salt water and limescale mainly attack the luminaire bodies and gaskets: favour 316L stainless steel or a plastic material intended for immersion, then rinse the glass and check the gasket each season. During winterising, the light stays in place, underwater, and you avoid switching it on dry.
Can you switch on a pool light out of the water?
No, in most cases: without water around the luminaire, the source heat is no longer dissipated and the glass or gasket suffers. Follow the manufacturer's instructions, which specify the mode of use. During filling or draining, cut the circuit power rather than testing briefly. Dimmable LED versions are then adjusted in brightness for the evening.
What to do if the light no longer comes on?
Work back along the line in order: power at the panel, condition of the transformer, then connection to the luminaire, and finally the source itself. A tired or flooded transformer explains more failures than a dead light. Only remove the plate after cutting the circuit, and change the gasket when reassembling. Black finishes get dirty less quickly on a dark coping.
Should you light only the pool or also the surroundings and the house?
Lighting the pool alone leaves the terrace in the dark as soon as you get out of the water. A line of spotlights recessed in the ground or the coping extends the light towards the entrance, the staircase and the dining corner, and the same discreet beam logic can serve inside the house.
How to harmonise pool lighting with the surroundings?
Keep a single family of colour temperatures across the whole garden: two different whites side by side give an improvised impression. Then light the path, not the void, aiming at steps and level changes. A lower intensity on the surroundings than at the water's edge is enough to create depth.
And indoors, where to place recessed spotlights?
The same desire for grazing light is found behind a worktop, above an island, along a living room wall. For the kitchen, the points are placed in front of the user and not behind them; this is the principle of successful kitchen decoration. A modern kitchen decor project plays on fine, aligned sources, then the living room takes over with recessed spotlights for the living room and, for light rooms, a discreet white colour that disappears into the ceiling.
Order from Designix
Record the niche, diameter, wall material and cable length, then choose the light temperature: it is the only sequence that avoids a returned parcel. Secure payment, tracked delivery, returns and Designix customer service accompany every order, and the team answers on compatibility before purchase.
Frequently asked questions
How to replace a bulb in a pool?
Cut the power at the panel, remove the plate or the glass depending on the model, then replace the source with a bulb of the same voltage, the same base and the same maximum power. The gasket is changed on reassembly, and the light is only switched on again once the pool is filled with water.
Do you need a transformer for a 12V pool light?
Yes: a 12V light is not connected directly to the 230V mains. You need a transformer or a 12V power supply suited to the luminaire power, installed outside the pool volume, in a ventilated and accessible place for maintenance and replacement.
Does a 12V pool light consume more than a 230V light?
No: at equal power, consumption is comparable. The difference between a 12V light and a 230V model lies in safety and wiring, not in the bill. What really counts is the source technology and the quality of the power supply.
Can you change the colour or light temperature of a pool light?
It depends on the model: some LED lights offer several selectable temperatures or colours, others are fixed in warm white or cool white at purchase. On a light with an interchangeable bulb, the colour follows the chosen bulb, provided the original voltage and base are respected.
Do you need an electrician to install a pool light?
The mains connection, the transformer and the equipotential bonding require a qualified professional, and fitting in an immersed wall requires a watertightness check. Replacing a 12V light already in place is then simpler, but the first installation involves the safety of the pool.





