Fluorescent strip light

This selection is also available in our French store: Réglette néon

No products in this selection.

  • Tracked delivery to your country Tracked delivery
  • Secure payment at checkout Multiple payment methods
  • 14 days to change your mind 14-day returns
  • Secure payment Secure payment
Designix guides you

Not sure of your style? Find it in 30 seconds

A few questions, and we will show you the pieces made for you.

Frequently asked questions

How do I choose the right product?
Check the dimensions, materials and reviews on each product page; our team can advise you before you buy.
What are the delivery times?
The estimated date is shown in the cart and at checkout.
Can I return an item?
Yes, you have 14 days to change your mind.
Can I pay in instalments?
Depending on your country, instalment payment options may be offered at checkout.
Fluorescent strip light
Designix · Design lighting

An interior that reflects who you are

Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.

  • Tracked delivery
  • Pay in instalments, where available
  • 14 days to change your mind
  • Advice & showroom in Lyon, France
Read our guide

Check three things before ordering: the length of the fitting, the cap (T8 in G13 most often, thinner T5) and whether a starter or ballast is present. These three decide whether a neon strip light slides straight into the batten already installed, or whether the wiring needs to be changed to direct 220 V supply.

What is the difference between classic neon and LED neon?

A classic neon is a fluorescent tube: a gas under low pressure lights up thanks to an electric arc, mercury is present in the tube, and ignition goes through a starter and a ballast. LED neon replaces the gas with diodes distributed behind a diffuser: immediate ignition, no mercury, stable light with no perceptible flicker.

The difference plays out at replacement time: a fluorescent tube is changed with its starter, sometimes its ballast, while an LED tube requires checking the compatibility of the fitting. To compare the available formats, browse the range of LED battens and, if you are looking for other light fixture shapes for the same room, all Designix light fixtures.

Classic neon or LED neon: what changes
Criterion Fluorescent tube LED tube
Light source fluorescent gas light-emitting diodes
Starter required removed on direct-supply models
Ballast mandatory bypassed or removed depending on the model
Cold ignition progressive immediate
Mercury present in the tube absent
Replacement tube and starter, sometimes ballast compatible tube or adapted wiring

How to replace a fluorescent tube with an LED tube?

First note the length of the tube and its cap, then open the fitting to see whether it contains a ballast and a starter. These two pieces of information determine the family of LED tube to order, and therefore the time spent on the ladder.

Neon batten without starter: what to remove

On a fluorescent setup, the starter housed in the socket or in the fitting is no longer used with a direct-supply tube. It is removed, and the ballast is taken out of circuit: the tube then receives 220 V directly on its pins. The fitting cover is put back once the connection has been checked.

Compatible tube or direct supply: how to decide

The compatible tube is fitted without touching the wiring: time is saved, the original fitting is kept. Direct supply removes the ballast, which avoids a wear part, but requires an intervention. If the fitting is old or if the ballast hums, the second solution is the healthier one.

How to wire an LED neon without a starter?

Without a starter, the direct-supply LED tube receives 220 V on the pins of its sockets: the starter is removed, the ballast bypassed or removed. On a new fitting designed for LED, the connection is already done. Always switch off the power at the circuit breaker before working.

How to fit an LED neon on an old fitting?

Identify the cap and the length, then locate the wires arriving at the sockets. The manufacturer's diagram shows which pin receives the live and which receives the neutral. If the sockets are cracked or the contacts blackened, replace the whole batten rather than patching up a tired fitting.

What to check on the socket before reconnecting

Clean contacts, straight pins, no bare wire touching the metal sheet. Check that the connections are tight, reposition the diffuser, then restore the power. Comparing models is easy in the 220 V battens, and for a wall-mounted setup, wall lights and wall battens open another path.

Unsure which model to fit? Length and cap first, the collection will be completed as soon as references are available.

Which neon batten length to choose: 50, 120 or 150 cm?

The length follows two constraints: the surface to be lit and the space actually available. A batten that is too long overhangs the cabinet, one that is too short leaves shadow areas on the worktop. Measure the existing fitting and the fixing centres before ordering.

50 cm neon batten: for what use?

A short batten lights a cupboard, a cellar, a shelf or a narrow worktop. It is also the format that slides under a low cabinet without overhanging. In a corridor or a wardrobe, a batten with motion detector saves you looking for the switch with your hands full.

120 cm or 150 cm neon batten: measure before ordering

120 cm covers a kitchen or a garage, 150 cm a workshop or a long corridor. Check the reach of the ceiling fixings and the free space around the tube to turn it a quarter turn. For a cellar without a nearby socket, rechargeable battens without a socket simplify installation.

Choosing the length of your neon batten
Length Where it fits What it lights To check before buying
50 cm cupboard, cellar, under-cabinet a short worktop or a shelf fixing centres and cap type
60 cm corridor, wardrobe, low cabinet a narrow passage length of the existing fitting
120 cm kitchen, garage, utility room a worktop or a workbench cap and supply mode
150 cm workshop, long corridor, barn a large floor area reach of the ceiling fixings

Where to install a neon batten: kitchen, garage or workshop?

In the kitchen, the batten is fixed under the wall units to light the worktop without casting shadows. In the garage and the workshop, it is mounted on the ceiling above the workbench. In a bathroom or utility room, choose a model protected against humidity, outside the bath zone.

Kitchen neon batten: under the wall units

Choose a slim model, long enough to cover the worktop, and avoid placing it directly above a hob: steam and splashes dirty the diffuser. Even light is better than a very bright point that dazzles when seated. Also see the bathroom batten if the room is humid.

Garage neon batten: height and fixings

Above a workbench, the batten is fixed high enough not to hinder the passage of a plank, low enough to light your hands. Check the strength of the fixings in a slab or a roof structure. For a work room, regular workshop light and lighting a garage detail the configurations.

IP65 waterproof neon batten: for what uses outdoors and in damp rooms?

The IP rating describes the protection against dust and water: an IP20 is suitable for a dry room, an IP65 resists dust and water jets. Choose it for a canopy, a damp garage, a utility room or a cellar, never as a decorative argument in a living room.

Outdoor LED neon: under a canopy or shelter

Under a canopy, the batten receives lateral splashes even without direct rain: the diffuser gasket and the cable gland make the difference. Compare our outdoor solutions and the waterproof outdoor models according to the actual exposure.

Damp room: which protection rating to choose

In a bathroom, the batten is mounted above the mirror, outside the safety volumes around the bath. In a utility room or a cellar, waterproof battens and IP65 protected models cover everyday use. For a room washed down with a hose, linear lighting resistant to humidity remains the safe choice.

My neon flickers but does not light up, what should I do?

A neon that flickers without lighting indicates a tired starter, a tube at the end of its life or a dirty socket contact. Switch off the power, inspect the socket, then replace the tube first and the starter next. On a direct-supply LED tube, a ballast still in place gives the same symptom.

The tube flickers: starter or tube at the end of its life?

On a fluorescent setup, the starter is the cheapest and easiest part to change: try it first if the tube is recent. If the flickering persists with a new tube and a new starter, the ballast is at fault and the fitting deserves to be replaced.

It lights up then goes out: check the socket contact

A tube that lights up then goes out after a few seconds often reveals a badly seated pin or an oxidised contact. Switch off the circuit breaker, remove the tube with a quarter turn, clean the contacts and check that the sockets do not turn in the fitting.

Which cap and fitting to plan for an LED neon batten?

The cap depends on the fitting already installed: a T8 tube with G13 cap equips most tube battens, the T5 has a thinner cap and a different fitting. Note the length, cap and supply mode before buying. Fixings and connection are supplied with the batten or to be planned depending on the model.

G13 or T5 cap: recognising your fitting

The G13 corresponds to the spaced pins of the T8, the most widespread format in garages and kitchens. The T5, thinner, is found in furniture and compact setups. Measure the tube diameter and the pin spacing: these two dimensions are enough to identify the right model. For a setup with detection, integrated mains detection connects like a classic batten.

Integrated batten or tube fitting: what is the difference

The integrated batten arrives with its diffuser, its driver and its fixings: you install it and connect it. The tube fitting, on the other hand, takes a separate tube, which makes changing the source easier but requires checking compatibility each time. In both cases, careful marking saves a round trip.

Secure payment, tracked delivery, returns and Designix customer service accompany every order. The choice comes down to three dimensions, not the length of a page: browse the LED battens or the complete light fixture catalogue to find the format that matches your fitting.

Frequently asked questions

How to wire a neon tube?

Switch off the power at the circuit breaker, then present the tube aligned with the sockets and turn it a quarter turn until it locks. On a fluorescent setup, the starter is in place before restoring the power. Check that it lights before closing the diffuser.

Is it possible to fit an LED neon on a standard fitting?

Yes, if the length and cap match, the T8 in G13 being the most widespread. The point to decide remains the supply: a tube compatible with the existing ballast, or a direct-supply tube that requires modifying the wiring. This check is done before buying.

How to fit an LED neon on an old fitting?

Identify the cap and the length of the fitting, then the type of tube accepted. On a direct-supply model, the starter is removed and the ballast bypassed. If the fitting is old, check the condition of the sockets and contacts before restoring the power.

My neon flickers but does not light up. What should I do?

Switch off the power, then check the socket and its contacts, often dirty or loose. Then replace the tube, then the starter if the setup has one. On a direct-supply LED tube, a ballast still active produces the same flickering and must be removed from the circuit.

Where to find a neon tube?

In a DIY store, from an electrical equipment distributor or online from a lighting specialist. Identifying it beforehand matters more than where you buy: length, cap and supply mode determine the tube compatible with your fitting.

Our advice for choosing
The neon batten light illuminates a worktop, a workbench or a passage with a linear and even light. This page explains how to identify its mount, choose the right length and base, then wire an LED tube with or without a starter, indoors as well as in damp rooms.