Black LED strip lights
This selection is also available in our French store: Réglettes LED coloris noir
No products in this selection.
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right product?
What are the delivery times?
Can I return an item?
Can I pay in instalments?

An interior that reflects who you are
Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
Allow one strip light per linear run to be lit: measure the available length, set the colour temperature for the room, then check the ingress protection rating before ordering. A black profile blends into a dark ceiling or a roof structure and lets the white light do the work.
What light does a black LED strip light give?
A black LED strip light gives a direct white light, spread along its whole length by its diffuser, with no hot spot and no shadow zone. The black housing stays discreet on a dark ceiling and underlines the lines of a roof structure. The colour temperature chosen, warm, neutral or cool, decides the atmosphere in the room.
Black LED strip light, a continuous line of light
The opal diffuser spreads the light along the whole length of the profile: no bright spot in the middle, no dark zone at the ends. That is what sets a strip light apart from a simple bulb screwed to the ceiling. Seen from below, the black line frames the light and makes it crisp, with no diffuse halo. In a garage or above a worktop, that evenness matters more than raw power: you see what you are doing, with no shadow cast by your hand.
Warm, neutral or cool white: the atmosphere changes
Colour temperature is read in kelvins on the product sheet. It does not describe power but the tint of the white, and it is what makes a room feel welcoming or technical.
| Colour temperature | Atmosphere given | Suitable room or use |
|---|---|---|
| Warm white (around 3000 K) | Soft light, close to incandescent | Kitchen, dining area, living room |
| Neutral white (around 4000 K) | White light with no dominant tint | Workshop, worktop, utility room |
| Cool white (around 6000 K) | Crisp, high-contrast light | Garage, cellar, technical room |
To compare the available options, browse all the LED strip lights in the catalogue and filter by white temperature.
Where to install a black LED strip light in the home?
In a garage and a workshop, the strip light goes on the ceiling, above the worktop or the bench. In a kitchen, it goes under the wall unit to light the prep surface. A bathroom or a cellar calls for a model protected against moisture, and outdoors a model rated for outdoor use.
On the garage ceiling or above the bench
In a garage, the strip light is placed perpendicular to the door or along the line of the car, at ceiling height, to light the bonnet and the floor without glare. Above a bench, it sits about one metre from the worktop, slightly in front of your head so it does not cast the shadow of your hands. Dedicated models are gathered in lighting a garage with a strip light and in models designed for the workshop.
Under a kitchen unit or in a bathroom
Under a wall unit, a slim strip light is fixed to the front of the cabinet, on the worktop side, so the light falls on the prep surface and not behind you. In a bathroom, it is installed outside direct splash zones, with a protected model: see bathroom lighting. For a terrace or a canopy, go to outdoor installation. The whole range is in the Designix lighting department.
| Room or use | Type to favour | Point to check first | Protection to aim for |
|---|---|---|---|
| Garage | Fixed strip light, length covering the work area | Length and power | Protected model if damp |
| Workshop | Strip light placed above the bench | Light distribution | Protected model if dusty |
| Kitchen | Slim strip light under the wall unit | Footprint and fixing | Standard model in a dry zone |
| Bathroom | Strip light protected against splashes | Ingress protection rating | IP44 or higher |
| Cellar, utility room | Watertight strip light, possibly with sensor | Moisture and hands-free switching | IP44 or higher |
| Terrace, canopy | Strip light rated for outdoor use | Exposure to rain | IP65 |
How to choose the length and power of a black LED strip light?
First measure the available length, then choose the power according to the surface and the mounting height: a large garage does not call for the same strip light as a cupboard. Colour temperature and the presence of a sensor or a switch matter as much as the power stated on the sheet.
Length and light points: measure before ordering
Take the measurement between the two walls or between the two ends of the unit, then allow a few centimetres on each side for fixing and cable access. A strip light that is too long cannot be cut down: the length is fixed, unlike a tape. Over a wide work area, two short strip lights in line are better than a single off-centre one, because the light is spread better on both sides.
Power and output: aim for the use, not the maximum
A corridor or a cupboard needs little; a worktop or a bench needs more, because you read, cut and tinker there. The higher the mounting, the more power you need to get the same illuminance on the floor. The product sheet gives the power and sometimes the output in lumens: note the power, and rely on the in-store result if you are unsure about the output. For circulation use, stay modest; for work use, aim higher.
Black LED strip light 220V or rechargeable: which power supply to choose?
A 220V LED strip light connects directly to the mains and switches on continuously as soon as you press the switch. A rechargeable model can be installed without a socket or wiring, but it has to be recharged and does not last as long when switched on. The choice therefore depends on whether there is an electrical supply where you want it.
220V connection: fixed and permanent
If there is an electrical supply on the ceiling or behind the unit, 220V remains the simplest solution in use: no recharging to monitor, immediate switching, discreet installation. The relevant models are gathered in strip lights to connect to the mains. Switch off the power before connecting and check that the terminal block accepts the cross-section of the cable in place.
Rechargeable model: no socket nearby
In a cupboard, a cellar without electricity or under a shelf far from any socket, a battery version saves running a cable. It switches on on demand and recharges by cable. The trade-off is real: you have to remember to recharge it and the battery life drops with use. The rechargeable versions without wiring are therefore suited to occasional lighting, not to a room occupied all day.
Do you need a watertight black LED strip light for a damp room or outdoors?
The ingress protection rating describes resistance to dust and water. In a dry room, a standard model is enough; in a bathroom, a cellar or under a canopy, you need a strip light protected against splashes; outdoors and exposed, choose a model rated for outdoor use.
IP44 and IP65: what the rating really protects
The first digit concerns solids, the second liquids. An IP20 is a bare model, intended for a dry, dust-free room. An IP44 resists water splashes from all directions, which covers a bathroom or a utility room. An IP65 also withstands water jets: that is the level to aim for under a canopy or on a terrace. Models rated this way are found in high ingress protection rating.
Bathroom, cellar, terrace: the cases that call for watertightness
A bathroom, a cellar or an unheated garage experience condensation and moisture: go for the watertight models for damp rooms. For a covered terrace, check the outdoor mention on the sheet. In the open air, with no shelter, you need a reference rated for exposed outdoor use, such as those in watertight outdoor references.
LED strip light with motion sensor: for which use?
The motion sensor switches the strip light on as you pass and off after a period of inactivity: handy in a garage, a corridor or a cellar where you go in with your hands full. It saves forgetting to turn the light off and comes in a mains-connected or battery version.
Quick pass-through: garage, corridor, cellar
The sensor is useful where you pass without stopping: garage entrance, cellar stairs, service corridor, deep cupboard. It does not replace a switch in a room where you stay seated, because the light goes off while you are still there but not moving. Detection is usually adjustable in range and delay, which avoids unwanted switching. See strip lights that switch on as you pass.
220V sensor or battery model
With an electrical supply, the mains-connected version stays on with no time limit and needs no charging maintenance: it is the choice of sensors combined with a 220V supply. Without a socket, the battery version helps out in a cellar or a storeroom, provided you accept regular recharging.
Cuttable LED tape or LED strip light: how does it work?
A cuttable LED tape is cut on marks printed every few centimetres and reconnected with a connector. A strip light is installed as it is, at its length, and connects to the mains. The tape adapts to corners and furniture, the strip light lights a circulation area or a worktop.
The tape is cut on printed marks
Cutting is only possible at the marks printed on the circuit, never between two. Once cut, the tape is reconnected with a connector or a suitable terminal block, and it runs on low voltage with a dedicated power supply. It is the solution for niches, furniture corners and irregular lengths, where a rigid strip light does not fit.
The strip light is installed as it is, without cutting
The strip light arrives at its length, with its profile and diffuser already fitted. It is fixed with clips or screws and connects to the mains. It is preferred when the line to be lit is straight and the standard length matches: less preparation, a crisper result, and better-spread light than a bare tape. The full comparison is in the strip light collection by use.
How to install and maintain a black LED strip light?
A strip light is fixed to the ceiling or the wall with clips or screws, depending on the surface and the weight of the profile. Switch off the power before connecting, locate the cable entries and check it is level. The black profile is cleaned with a soft cloth, with no abrasive product on the diffuser.
Fixing: clips or screws depending on the surface
On plasterboard ceilings, spring clips are enough for a light profile and avoid drilling. On concrete, on a roof structure or for a long model, screws remain safer. Locate the cable entry before screwing, draw the line in pencil, check it is level, then tighten. Switch off the power at the breaker before any connection and test the light with the diffuser in place.
Cleaning the black profile without damaging the diffuser
Dust the profile with a dry microfibre cloth, then wipe the aluminium with a slightly damp cloth. The opal diffuser is cleaned without abrasive product or alcohol, which can dull the plastic. Avoid water jets, even on a protected model: the rating describes resistance, not an invitation to hose it down.
A black line that underlines the ceiling
Align the strip lights with each other and with the lines of the room: beam, wall, row of units. A continuous black line reads as an architectural feature and not as an added accessory. Before ordering, take a look at our selection of light fittings to match the strip light with the rest of the lighting.
Frequently asked questions
What is the best LED strip light?
There is no best strip light in absolute terms: the right one depends on the room, the available length and the power supply possible on site. Look at colour temperature, ingress protection rating and fixing before comparing models, not just the stated power.
What are the drawbacks of LED lamps?
LEDs heat up little and last a long time, but they cost more to buy and their light can feel cold if you choose a high temperature. Some entry-level models flicker or render colours poorly. The module is sometimes sealed: at end of life, the whole strip light is replaced.
How to choose a black LED strip light?
Measure the available length, choose the power according to the surface to be lit, then set the colour temperature you want. Then check the ingress protection rating if the room is damp and whether there is a switch or a sensor where it will be installed.
Can a black LED strip light be installed in a bathroom?
Yes, provided you choose a model protected against water splashes, not a bare strip light intended for a dry room. Keep it away from zones directly exposed to splashes and check the ingress protection rating stated on the product sheet before installation.
Does a 220V LED strip light need a transformer?
Generally no: a strip light designed for 220V has its power supply built in and connects directly to the mains. A separate transformer or driver is only needed on low-voltage models, supplied with their power supply. Check the model sheet before connecting.
Ordering a black LED strip light from Designix
Once the length, colour temperature and ingress protection rating are noted, all that remains is to choose the model that ticks all three. Browse the LED strip lights by use and the general lighting catalogue to match the strip light with the rest of the room.
- Secure payment
- Tracked delivery
- Returns
- Designix customer service





