60 cm neon
This selection is also available in our French store: Néon 60 cm
No products in this selection.
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right product?
What are the delivery times?
Can I return an item?
Can I pay in instalments?

An interior that reflects who you are
Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
A 60cm neon light measures 600 mm in length and is chosen first by its base: G5 for a T5 tube, G13 for a T8. Then check the fitting's power supply, the desired colour temperature and the room's protection rating before ordering.
What is a 60cm neon light and what does this length correspond to?
First measure the gap between the sockets of your fitting: a 600 mm tube only fits a luminaire designed for that dimension. It is the length of short linear fittings, the ones that sit under a shelf, at the back of a pantry or above a worktop.
60cm neon light: the 600 mm format and its bases
The 60 cm corresponds to 600 mm excluding sockets. A 60cm neon tube clips onto two pins, and both the number and the spacing of these pins vary by family. A T8 tube uses a G13 base, a T5 uses a G5 base. A 60 cm model therefore never replaces a one-metre tube, and a T5 does not fit a T8 fitting. To see models in this length, browse clip-on LED neons.
60cm LED or fluorescent neon: what changes on the fitting
The fluorescent needs a ballast and, on many setups, a starter. The LED tube, on the other hand, is powered directly: sometimes from one end, sometimes from both. This difference decides compatibility with your existing luminaire. The rest comes down to diameter, covered further below.
What is the difference between a neon and an LED?
The difference shows at switch-on: an LED tube lights up instantly, with no flicker or warm-up time, whereas a fluorescent takes a few moments and becomes less consistent at low temperatures. It can then be checked inside the tube.
Neon or LED: what it changes in use
A fluorescent tube contains a gas excited by the ballast; an LED tube lines up diodes behind a diffuser. The first depends on a ballast and starter set, the second on a simple power supply. In use, this means immediate light and a colour temperature that is easy to read on the packaging, in kelvins. The same room lit in warm white, around 3000 K, does not look like lighting in cool white, around 6000 K.
Why the LED tube replaces the fluorescent tube in small linear fittings
At 60 cm, there is little room for a bulky ballast set. The LED tube simplifies installation and comes in the common colour temperatures, so the lighting can be matched to the room. This is why switching to LED neon has become the default choice for renovating small linear fittings.
60cm neon light 18 W or 36 W: how do you read the stated wattage?
The wattage indicates the tube's consumption, not the amount of light it gives out. Two 60 cm tubes of the same wattage can produce very different results depending on their efficiency. So compare wattage, colour temperature in kelvins and the stated output, without stopping at the single figure on the packaging. For the same use, a more powerful tube often lights more strongly, but also consumes more: it is up to you to decide according to the area to cover and the daily burn time.
How do you choose a 60cm neon light by room: kitchen, workshop, aquarium?
The starting point is not the tube but the area to light. A worktop wants bright light with no cast shadow, a workshop a closed luminaire that withstands dust, a tank a stable colour temperature. Colour temperature and protection rating matter as much as length.
| Room or use | What you expect from the light | Criterion to check | Recommended format |
|---|---|---|---|
| Kitchen worktop | Bright light cast on the surface, with no shadow on the plate | Neutral to cool colour temperature, even diffuser | 60 cm tube in an under-cabinet strip light |
| Utility room, garage, workshop | Seeing what you are doing, withstanding dust | High protection rating, closed luminaire | 60 cm T8 in a closed luminaire |
| Aquarium | A stable colour temperature that does not distort the tank's colours | Protection rating suited to humidity | 60 cm tube designed for aquariums |
| Display case or shop | A continuous, discreet linear light | Aligned tubes, single-ended power supply | 60 cm T5 or T8 depending on the fitting |
| Cupboard, wardrobe, pantry | Close lighting that takes up no space | Short format, compact size | 60 cm strip light |
Above a tank, splashed water and condensation require a protected tube: a high IP rating, generally at least IP44 in a damp area, remains a trade reference to confirm with the luminaire's instructions. For the kitchen, a kitchen neon placed directly above the worktop prevents your shadow falling on the chopping area. If under-cabinet installation is impossible, a neon wall light solves the problem at height. The rest of the full lighting catalogue covers the rooms where a tube alone is not enough.
Can you replace a 60cm neon light with an LED tube in an old fitting?
Yes, provided you read the luminaire's label before buying. The LED tube replaces the fluorescent if the fitting accepts the same base and if the power supply matches, whether single or double-ended. Some setups require removing the starter and bypassing the ballast.
How do you wire an LED neon without a starter?
Switch off the power at the circuit breaker, remove the old tube, then the starter if it is accessible on the side of the luminaire. The ballast is bypassed following the diagram supplied with the tube. A tube designed for single-ended power supply is not wired like a double-ended one: this is the point that causes the most failures on reassembly.
How do you fit an LED neon in an old fitting?
Note the length, the base and the type of power supply, then choose a compatible tube. If the fitting is worn or the wiring is uncertain, a complete new luminaire often costs less than a repair. See LED neon for old fittings before ordering, and for a hallway, a neon wall light in a hallway avoids running an extra line.
What is the difference between a T5 neon tube and a T8 neon tube?
T5 and T8 refer to the tube's diameter, never its length: about 16 mm for a T5, about 26 mm for a T8, for the same 600 mm. The T8 with G13 base is the most widespread format in renovation; the T5 with G5 base equips slim luminaires and compact strip lights.
| Criterion | T5 tube | T8 tube |
|---|---|---|
| Tube diameter | About 16 mm | About 26 mm |
| Base | G5 | G13 |
| Appearance | Fine, discreet line under a cabinet | Bulkier, more visible tube |
| Host fitting | Strip lights and compact luminaires | Luminaire with T8 sockets, common in renovation |
| Replacing a fluorescent | Compatible T5 fitting required | Common substitution with a T8 LED tube |
| Check before | Length, base, power supply | Single or double-ended power supply, starter |
A T8 can be recognised by its wider diameter and spaced pins: it is the tube found in most luminaires installed over recent decades. The T5 is preferred when thickness is a problem, under a low shelf for example. To compare available lengths, see LED neon tubes in all lengths. Before buying, a look at choosing a luminaire suited to the room avoids forcing a tube into an unsuitable fitting.
Are neons banned in France?
Fluorescent tubes do not disappear overnight from luminaires already installed, and an LED neon is not affected: it runs on diodes, without mercury. What is changing is the availability of fluorescent tubes, gradually replaced by LED tubes in common formats such as 60 cm.
Fluorescent neon and mercury: what to know before throwing away
A used fluorescent tube contains mercury and must be taken to a waste centre or collection point, never put in ordinary household waste. An LED tube has no such constraint. This is a practical argument, not a sales pitch: check the marking on the tube you are removing.
60cm LED neon: the solution for an existing luminaire
When the fitting is still sound, the LED tube is enough to bring the linear light back into service. For wall mounting, the neon wall light at height is a worthwhile replacement for a bare tube on a staircase. And if the room is a kitchen, lighting a worktop remains the most common use case.
How do you fit and maintain a 60 cm neon?
Switch off the power before any handling, then fix the clips or the two brackets designed for the tube's diameter, under a cabinet as on the ceiling. Push the tube fully into its sockets and check that it does not flex before restoring power.
Fitting a 60cm neon light to the ceiling or under a cabinet
An under-cabinet fitting is screwed into the bottom of the cabinet, never into the worktop. On the ceiling, the brackets are spread along the whole length to prevent the tube from hanging in the middle. A tube longer than the fitting will break on reassembly: the measurement is taken including sockets.
Cleaning a 60cm neon light without damaging the diffuser
Dust dry, with a soft cloth or microfibre. Water and household products mark the diffuser and can seep in if the luminaire is not designed for it. Regular dusting is enough to keep the light output, especially in a kitchen where grease settles. For a kitchen linear light, prefer a closed model, see under-cabinet kitchen neon.
- Secure payment
- Tracked delivery
- Returns
- Designix customer service
Still unsure between a T5 and a T8? Compare the available models and their colour temperature in switching to LED neon, or browse the Designix lighting range for the rooms where a tube alone is not enough.
Frequently asked questions
What is the LED equivalent of a 60 W bulb?
The match between a 60 W bulb and an LED is read in lumens, not watts: aim for the equivalent luminous flux, then take into account the tube's length and base. For a 60 cm tube, also check the colour temperature if you need to choose between several shades (switchable CCT).
A 60 cm LED tube is not compared to an incandescent bulb by its wattage alone: the amount of light and the use decide. Look at the efficiency stated by the manufacturer, the colour temperature, and the way the tube lights the surface. Two similar wattages can produce different results.
How can I replace neons with LEDs?
Note the base and length of the tube in place, switch off the power, then choose an LED tube compatible with the fitting. Depending on the model, the starter is removed and the ballast is bypassed. Check the colour temperature before reassembling everything, then restore power once the tube is fully engaged.
60cm neon light 36 W: what is this wattage for?
A 60 cm tube rated at 36 W consumes more than an 18 W of the same format. This wattage says nothing about the quality of the light: never compare it on its own. Look at the colour temperature, the stated output and the protection rating according to the room where the tube will be installed.
What is the exact length of a 60 cm neon tube?
A tube sold as 60 cm measures 600 mm in length, excluding sockets. On an old luminaire, this dimension is not enough: you must also check the socket spacing and the tube diameter. A T5 and a T8 of the same length do not fit the same fitting.
60cm LED neon with single-ended power supply: is it compatible with my fitting?
A single-ended tube receives current through one end, the other remaining neutral. It cannot be fitted to a double-ended wired fitting without modification. Read the luminaire's diagram or the tube's label before ordering, and switch off the power to check the wiring.





