12V LED strips
This selection is also available in our French store: Rubans LED 12V
No products in this selection.
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right product?
What are the delivery times?
Can I return an item?
Can I pay in instalments?

An interior that reflects who you are
Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
Count on a 230 V to 12 V transformer between the socket and the strip, or a battery if the installation is in a vehicle: it is this low voltage that makes the 12V LED strip thin, flexible and free of dangerous contact. It sticks under a cabinet, along a skirting board or in a cabin, and lights in a continuous line rather than in a spot.
What is a 12V LED strip and what light does it give?
A 12V LED strip is a flexible band of diodes powered at low voltage, by a 230 V to 12 V transformer, a battery or a cigarette lighter socket. It lights up close, in a continuous line, with no visible hot spot on models with closely spaced LEDs, and sticks under a cabinet, in a corner or along a skirting board.
Low voltage, and what it requires
Between the mains and the strip, you need a transformer or driver that steps the voltage down. Place it in an accessible, ventilated spot, not at the bottom of a closed box: it is the part that gets replaced one day. Allow for the cable length between the transformer and the start of the strip, and keep in mind that a very long run loses intensity at its end. The rest of the Designix lighting catalogue follows the same power supply logic.
COB or SMD: what the eye sees
An SMD strip lines up small separate diodes: at a short distance from the surface, dots are visible. A COB strip shows a continuous luminous trail, with no break, which matters for grazing a worktop or a cabinet outline. In both cases, the light is indirect and lateral: it highlights a material, it does not light a whole room.
Where to install a 12V LED strip: kitchen, cabinet or vehicle?
Under a kitchen worktop, along a skirting board or around a TV unit, the strip goes where light is missing and no fixture fits. In a vehicle, it follows the cabin walls. Each location imposes its constraint: access to a socket, cable routing, a surface that accepts the adhesive.
| Use | Strip type | Target IP rating | Recommended colour | To check |
|---|---|---|---|---|
| Under a kitchen cabinet | Bare strip or in aluminium profile | IP20 | Warm white 2700 K or 3000 K | Run length and access to a socket |
| Camper van, van | Flexible strip on auxiliary battery | IP20 to IP44 | Warm white | Cable gauge, fuse and fixing |
| Car | Strip on cigarette lighter socket or dedicated circuit | IP20 | White or RGB | Cable routing and adhesion |
| Bathroom, covered terrace | Waterproof strip in profile | IP65 | Warm white or RGB | Sealing of connections and transformer |
| Pool, pond | Low-voltage strip designed for immersion | IP68 | White or colour | Power supply out of water and installation compliance |
| Skirting board, TV unit outline | Thin or COB strip with no visible dots | IP20 | Neutral white or RGB | Even rendering in corners |
12V LED strip for camper van and van
The strip taps into the vehicle's 12 V circuit or an auxiliary battery, protected by a fuse. Laminated furniture and panelled walls hold the original adhesive poorly: a screwed aluminium profile solves the problem and acts as a heat sink. Check the polarity before powering up, and run the cable clear of door edges.
12V LED strip for car
The cigarette lighter socket remains the simplest setup, with no vehicle modification, using a 12 V adapter. For a discreet result, a dedicated fused circuit is cleaner. Avoid the hot areas of the engine bay and passages where the cable gets pinched. For coloured ambiences, RGB strips are controlled by remote.
Waterproof 12V LED strip: which one for outdoors?
A waterproof 12V LED strip is recognised by its IP rating: IP65 for a covered terrace or a bathroom, IP68 for use in a pond. The strip must be protected along its entire length, connections included, and the transformer placed out of water, in a suitable enclosure.
Waterproof 12V LED strip: reading the IP rating
The scale is simple: IP20 means a bare strip, reserved for dry interiors. IP44 withstands splashes, IP65 water jets, IP68 prolonged immersion. A high rating on the strip is not enough if the ends are left open. See waterproof LED strips for damp rooms.
Outdoor 12V LED strip: think about the connections
Outdoors, water stagnates in poorly drained profiles: drill a drain hole and avoid dips. The transformer stays indoors or in a closed enclosure, never hanging in the rain. At the edge of a pond, an out-of-water power supply is the rule, and pool lighting requires equipment designed for immersion.
12V LED strip on battery: how to power it?
A 12V strip can run on a car battery, a camper van battery or a portable battery, provided the voltage is respected and the circuit is protected by a fuse. The duration depends on the battery capacity and the power actually consumed by the strip, not on its length alone.
On an auxiliary battery, with a fuse
The fuse goes as close as possible to the positive terminal: it protects the cable in case of a short circuit, not just the strip. A switch or relay prevents draining the battery when the vehicle is asleep. Before connecting, check the actual voltage at the terminals: a discharged battery gives dim light, a charger running can push it higher.
USB or cigarette lighter: simple setups
A cigarette lighter to 12 V adapter is enough for a short strip. The USB socket suits small sections, with available current limited by the charger. In both cases, respect the connector polarity and never power a 12 V strip directly from a mains socket.
Cuttable LED strip: how does it work?
A cuttable strip is cut at the marked points, every group of LEDs, never in between. Locate the copper pads, cut straight, then connect with a connector or solder while respecting polarity. Cutting elsewhere switches off the following section.
Locating the cut mark
Small lines and a scissors symbol indicate the permitted spot, usually every two or three groups of diodes. Cut in the middle of this zone, perfectly perpendicular, with a craft knife on a hard surface: a slanted edge makes the connector unusable. Measure the actual length before cutting, not after.
Connecting two sections without polarity errors
The + and - pads are marked on the circuit. A clamp connector works for a quick setup; solder holds better in a vibrating vehicle. Check the direction before sticking, then insulate the joint with heat-shrink tubing. If you extend a long run, 24V LED strips limit the loss at the end of the strip.
12V or 24V LED strip: what difference for a long run?
Both 12V and 24V run at low voltage, the difference lies in length: voltage drop comes sooner in 12V, which dims the end of a long run. 24V holds the distance better, 12V remains the standard for vehicles and small installations.
| Criterion | 12V LED strip | 24V LED strip | 220V LED strip |
|---|---|---|---|
| Power supply | 230 V to 12 V transformer, battery or cigarette lighter | Dedicated 24 V driver | Directly on the mains |
| Length of a single run | Limited by voltage drop | Tolerates longer lengths | Works in sections connected to the mains |
| Voltage in the strip | Low voltage | Low voltage | Mains voltage |
| Damp rooms and outdoors | Possible with a high IP rating and protected transformer | Possible with a waterproof driver | Reserved for products designed for this use |
| Typical use | Vehicle, cabinet, battery | Long continuous line in a living room | Long length with no visible transformer |
When to stay at 12 volts
12 V is essential as soon as there is a battery in the installation: car, van, camper van, portable site battery. It also suits small cabinet runs, where the transformer is easy to hide and the length stays short.
When to switch to 24 volts
Beyond a run that spans an entire room, 24 V keeps an even light from one end to the other. The driver is then chosen for this voltage. If no low-voltage supply can be housed, 220V strips connect directly to the mains, with the precautions that requires.
Which light colour for a 12V LED strip?
2700 K gives a golden white for the living room and bedroom, 3000 K a slightly crisper white for the kitchen and bathroom. RGB offers saturated colours without a dedicated white; RGBW adds a separate white, more accurate for everyday lighting.
2700 K or 3000 K: the ambience before the number
Below 3000 K, the light leans yellow and relaxes a room in the evening. Around 3000 K, it stays warm but renders food and tiles better. A neutral, cooler white suits a garage or a dressing room. Compare warm white 2700 K and 3000 K strips before deciding.
RGB or RGBW: what difference?
An RGB strip mixes three colours to obtain white, which often gives a slightly tinted white. An RGBW strip adds a dedicated white diode: colours stay vivid and everyday lighting stays accurate. For a cabinet outline as ambience, multicolour strips are enough; for a versatile living room, see RGBW models.
How to stick and maintain a 12V LED strip?
The strip sticks to a smooth, dry, dust-free surface, otherwise the adhesive gives way after a few days. An aluminium profile with diffuser protects the strip, evens the light and makes cleaning easier: a dry cloth is enough, with no abrasive product or immersion.
Preparing the surface before sticking
Degrease with a cloth and let it dry. On bare wood or a textured wall, the adhesive does not hold: use a screwed profile or a batten. Unroll the strip without bending it, tight turns are made with a corner connector. For lengths and damp rooms, the profile with diffuser remains the best base, and all LED strips are installed with the same gestures.
Cleaning the strip without damaging it
A dry or very slightly damp cloth is enough on a closed profile. No alcohol or abrasive on the sheath, no water jet on an IP20 strip. For regular dusting, the diffuser can be removed and refitted without touching the circuit.
Secure payment, tracked delivery, returns and Designix customer service: the order can be tracked from dispatch to receipt. To place a strip among all our light fixtures, start from the room and the use before comparing models, then refine with the LED strip range.
Frequently asked questions about 12V LED strips
12V LED strip for car: where to connect it?
The cigarette lighter socket is the simplest solution, with no vehicle modification, provided you use a 12 V adapter. For a discreet setup, a dedicated fused circuit is preferable. Avoid the hot areas of the engine and door passages where the cable gets crushed.
12V LED strip on battery: how long does it last?
The runtime depends on the battery capacity and the power actually consumed by the strip, not on its stated length. A high-capacity battery powers the same strip for longer. For regular use, add a fuse and check the voltage before connecting.
Waterproof 12V LED strip: can it be installed outdoors?
Yes, if the strip is protected along its entire length, ends and connections included, and if the transformer stays in a dry space or in a suitable enclosure. Outdoors, water stagnates in poorly drained profiles: provide a drain hole and avoid dips.
What is the difference between a 12V LED strip and a 220V LED strip?
The 12V strip runs at low voltage and requires a transformer, a battery or an adapter. The 220V strip connects directly to the mains and supports longer lengths, but mains voltage runs through the strip: installation requires more precautions.
Can a 12V LED strip replace an LED ceiling light?
It mainly lights indirectly, grazing a wall or a cabinet, and serves as accent rather than general lighting. To light an entire room, an LED ceiling light remains more suitable. The strip then complements it: outline, niche, under-cabinet or skirting board. Compare both in the guide to choosing a light fixture.





