Waterproof outdoor LED strips
This selection is also available in our French store: Rubans LED d exterieur étanches
No products in this selection.
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right product?
What are the delivery times?
Can I return an item?
Can I pay in instalments?

An interior that reflects who you are
Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
Before buying, check three things: the IP rating, the supply voltage and the actual run length you need to cover. Weatherproof LED strip lights illuminate a terrace, a canopy or the edge of a pond continuously, but this check is what decides whether they will last several seasons or fail in the first winter.
What are weatherproof LED strip lights?
Weatherproof LED strip lights are protected against water and dust by an IP rating, often IP65, IP67 or IP68. Silicone or resin encases the LEDs and the circuit. The higher the rating, the better the strip resists splashes, rain and then immersion.
Weatherproof LED strip lights IP65, IP67 or IP68: what is the difference?
IP65 withstands splashes and dust: this is the level for a canopy or a covered terrace. IP67 tolerates brief immersion, which suits a railing or a facade exposed to rain. IP68 is for prolonged immersion, under conditions set by the manufacturer.
| IP rating | Resistance | Typical location | To avoid |
|---|---|---|---|
| IP65 | Water splashes and dust | Under a canopy, a shelter, a covered terrace | Direct jets and immersion |
| IP67 | Short temporary immersion | Railing, exposed facade, terrace edge | Prolonged standing water |
| IP68 | Prolonged immersion according to the manufacturer | Pool edge, SPA, pond | Installation without checking voltage and connectors |
What silicone really protects on outdoor LED strip
The sheath or resin insulates the copper tracks and the solder joints, the weak points of a bare strip. They stop moisture from causing a short circuit and slow oxidation. This protection does not cover the ends: the cable gland and the connector finish the job. The weatherproof LED strip collection brings together sheathed and resin-coated models.
12 V or 220 V: which weatherproof LED strip lights to choose?
Weatherproof LED strip lights in 12 V or 24 V run on a transformer and stay off mains voltage near a pond. 220 V connects directly to the mains and suits long facades, provided the waterproof connectors and the circuit power are respected.
| Criterion | 12 V LED strip | 220 V LED strip |
|---|---|---|
| Power supply | Weatherproof transformer to be placed in a dry spot | Direct connection to the mains |
| Length per circuit | Limited by voltage drop, re-feeding possible | Long facade possible with waterproof connectors |
| Safety near water | Very low voltage, suited to poolside areas | To be reserved for dry, protected areas |
| Installation | Low-voltage cable easy to run along | Connection to be planned by a professional |
| Maintenance | Check the transformer and the junctions | Check the cable glands and the connections |
Weatherproof LED strip lights 12 V: transformer and safety
The transformer, or driver, steps down the voltage and must stay in a dry area, never in a flood-prone zone. Its power is calculated from the connected run length, with a margin, otherwise it heats up and cuts out. Near a pond, this low voltage simplifies installation: see the 24 V low-voltage LED strips.
Weatherproof LED strip lights 220 V: what to check
220 V avoids the transformer and allows long runs without voltage drop. In return, every junction must be waterproof and mechanically solid, with cable glands and a closed box. On a facade or under a dry shelter, it is the simplest solution: browse a 220 V outdoor LED strip before finalising your installation plan.
What length of weatherproof LED strip lights for my terrace?
The length of weatherproof LED strip lights is measured along the surface to be lit, not on the ground. Beyond several metres, voltage drop means you must re-feed the strip or choose a suitable cable gauge. Planning 10 m, 15 m or 30 m depends on the actual run length and the connectors.
Weatherproof LED strip lights 10 m or 15 m: how to measure?
Follow the path of the strip, corner by corner, with a flexible tape, and add the connection allowance. Ten metres cover the perimeter of a small terrace or a canopy; fifteen metres handle a medium terrace or the outline of a shelter. The length sold is never the usable length.
Weatherproof LED strip lights 30 m: avoiding voltage drop
Over thirty metres, the voltage gradually drops and the end of the strip dims. The answer lies in sections re-fed separately, or in a higher voltage with a suitable cable gauge. Compare the models in all LED strips according to the actual run length to cover.
Cuttable LED strip: how does it work?
A cuttable LED strip is cut at the marks provided by the manufacturer, at regular intervals depending on the model. Cut only when powered off, then close the end with a suitable waterproof connector. Cutting between two marks or through the printed circuit makes the strip unusable and compromises waterproofing.
Can you cut an LED strip that is too long?
Yes, at a cutting mark, with scissors or pliers. The cut section remains usable if it is re-fed through a waterproof connector. However, the resulting end is no longer protected: without an end cap or cable gland, moisture gets in and attacks the tracks.
Where to cut without losing waterproofing?
Cut exactly in the middle of the printed marks, never a few millimetres off. Close it immediately with a waterproof end cap from the same series as the strip. This finishing step is what makes an installation last, and it is also the point to check in the selection of weatherproof outdoor LED strips.
Where to install weatherproof LED strip lights?
Weatherproof LED strip lights are installed under a canopy, along a terrace, on a railing, on a facade or around a pond. Each location requires a suitable IP rating and a mounting that does not trap water. Avoid hollows where water collects and areas exposed to direct jets.
Under a canopy: outdoor ceiling LED lighting
Under a canopy, the strip runs along the beam and lights the table without glare: the light grazes the ceiling and comes back down. IP65 is usually enough, but a cleaning jet means going up one level. An aluminium profile ensures flatness and dissipates heat.
Terrace, railing, pool edge: the right IP ratings
On a railing or an exposed facade, water runs down: IP67 is the reasonable minimum. At the edge of a pond or a SPA, accidental immersion is possible and very low voltage is essential. Look at pool LED lighting and, for the shade, 3000 K LED strips which give a warm white without turning yellow.
How to install and maintain weatherproof LED strip lights?
Installation starts with a clean, dry surface, an aluminium profile that dissipates heat and waterproof connectors. The strip is glued or fixed without tension. Once a season, check the junctions, remove leaves and limescale, and make sure the transformer stays dry.
Which profile and mounting for a weatherproof LED strip?
The aluminium profile acts as a heat sink: a strip glued to a bare surface heats up and loses intensity. Choose a profile with a diffuser if the LED line must stay discreet. Fixing is done with clips or screws, never by tension on the power cable.
Cleaning and checking an outdoor LED strip season after season
A soft cloth and soapy water are enough; solvents dull the sheath. Check that the cable glands are tight and that there is no water in the boxes. To vary the shade of a lounge area, compare RGB LED strips and RGBW LED strips, the latter adding a dedicated white.
What are the best weatherproof LED strip lights?
There is no single best weatherproof LED strip for every use. The right choice depends on the location, the IP rating, the available voltage, the length and the type of light wanted. A strip suited to a pond is not the one that lights a dry facade.
The criteria that matter for an outdoor LED strip
In order: the IP rating actually needed, the voltage available on site, the run length to cover, the colour temperature and the quality of the connectors. A warm white around 2700 to 3000 K suits terraces; a more neutral white lights an outdoor worktop better. See 2700 K LED strips for a very warm ambient light.
Mistakes to avoid before buying
Overestimating the length a single circuit can handle, forgetting the transformer in a dry spot, cutting off-mark, neglecting the corners: these four mistakes come up most often. Also count the total consumption so as not to overload the power supply. To place the strip within a complete project, browse all our light fittings.
Choosing and ordering without mistakes
First identify the exact run length and the location, then the voltage, then the IP rating. This sequence avoids buying a strip unsuited to its surface. 24 V LED strips limit voltage drop over long runs, while 220 V LED strips simplify connection under a dry canopy.
At Designix, payment is secure, delivery is tracked and returns are handled by customer service. A question about an IP rating or a connector before confirming: Designix customer service answers before the purchase, not after. Find the references in weatherproof outdoor LED strips and the whole catalogue in our lighting catalogue.
Frequently asked questions about weatherproof LED strip lights
What are the best LED strip lights?
The best LED strip depends on the use. For outdoors, compare the IP rating, the voltage, the length, the colour temperature and the quality of the waterproof connectors. An IP68 12 V strip suits near a pond; an IP65 220 V strip is enough under a sheltered canopy.
Can you cut an LED strip that is too long?
Yes, provided you cut at a mark specified by the manufacturer. The strip then separates into a section that is still usable, to be re-fed with a waterproof connector. An off-mark cut breaks the circuit and leaves an unprotected end.
Cuttable LED strip: how does it work?
Locate the cutting mark printed on the strip, cut when powered off with scissors or pliers, then close the end with a waterproof connector. The cut section remains usable if it is re-fed. Cutting between two marks destroys the circuit.
Weatherproof LED strip lights 12 V: how to power them?
A 12 V strip is powered by a weatherproof transformer placed in a sheltered spot, with a power suited to the connected length. The low-voltage cable can run along the terrace. The transformer must never stay in a flood-prone area, even if the strip is IP68.
Can an IP68 weatherproof LED strip stay immersed?
An IP68 strip is designed for temporary immersion, not for permanent operation underwater without the manufacturer's verification. For a pond or a SPA, it must be powered at very low voltage and installed according to the product instructions. The IP rating does not replace safety rules. See also strips for ponds and SPAs.





