Recessed outdoor table lamps
This selection is also available in our French store: Lampes à poser d exterieur encastrables
No products in this selection.
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right product?
What are the delivery times?
Can I return an item?
Can I pay in instalments?

An interior that reflects who you are
Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
Plan for one recessed fixture per zone to be marked: a ground model along the path, a wall model near the threshold, a ceiling model above the table. The location decides the type of recess, the beam orientation and the protection rating before the style.
- Where to install a recessed light
- Terrace or path: which type
- Which IP rating
- Which light in the evening
- Wiring several lamps
- Installing ceiling spots
- E27 bulb and sockets
- Materials and style
- Maintenance and durability
Where to install an outdoor recessed light?
An outdoor recessed light goes into the ground to mark a path, into a wall or facade to signal an entrance, or into a terrace ceiling to light a table. The location sets the type of recess, the beam orientation and the protection rating to choose.
In which outdoor spaces should a recessed light be placed?
Path, terrace, facade, staircase, entrance, pool surround: each space has its own constraint. Along a path, the recessed light sits flush with the surface and lights the step without obstructing passage. On a facade, it draws a halo near the threshold or the house number. In a covered terrace ceiling, it lights the dinner table.
Ground, wall or ceiling recess: what is the difference?
In the ground, the housing goes into the slab or the base and withstands foot traffic. In a wall, it is recessed into the render or a dedicated box, at a height that avoids direct glare. In a ceiling or soffit, installation requires access from above for the connection. To compare lighting families, browse the Designix lighting catalogue.
Which type of recessed light for a terrace or a path?
For a path, a ground recessed light directs light toward the walkway without glare. For a terrace, a wall or ceiling model lights the table and the facades. The choice depends on the available height, the direction of travel and whether you want to illuminate or mark the way.
Ground recess to mark a path
Place the points on the side opposite the arriving step and aim the beam toward the ground, never toward the eye. Space them evenly to avoid dark gaps between two sources. A model whose trim stays flush limits the risk of catching the mower and the foot.
Wall or ceiling recess to light a terrace
A covered terrace benefits from two or three ceiling points, offset from directly above the table so no shadow falls on the plates. On the wall side, the recessed wall light signals the entrance and extends the light toward the ground. The adjustable lamps give an idea of the beam settings available elsewhere.
| Location | Type of recessed light | What it lights | Point to check |
|---|---|---|---|
| Path and garden | Ground, adjustable | The walkway and the steps | Resistance to water and foot traffic |
| Facade and entrance | Recessed wall | The threshold and the number | Fixing in the substrate and sealing |
| Covered terrace | Ceiling or soffit | The table and the surround | Clearance and connection |
| Outdoor staircase | Wall or step | The steps without glare | Beam orientation |
| Pool or wet area | Watertight ground or wall | The pool surround | IP rating suited to the exposure |
Which IP protection rating for an outdoor recessed light?
The IP rating indicates a light's resistance to dust and water. For an outdoor recessed light, it is chosen according to exposure: under shelter, on a facade or in the ground in a wet area. The exact value appears on the product sheet, not in a generic guide.
IP rating and real exposure: how to read the sheet?
The first digit concerns solids, the second liquids. In general, a point placed under an awning does not face the same splashes as a model flush with a lawn or near a pool. Common ratings range from IP44 (splashes) to IP67 (temporary immersion). A higher number never makes up for a sloppy installation.
Wet area, splashes, dust: the questions to ask
Ask where the light will actually be installed, whether it receives pressure washer jets, whether it stays submerged after rain. Also check water drainage around the housing. The design LED solutions show how the source and sealing are handled together on other lighting families.
Which light to illuminate a terrace in the evening?
A terrace is composed with two layers: ambient light, diffuse and low-glare, and functional light near the walkways and the table. Colour temperature and beam orientation matter more than the stated wattage, especially in a small space.
Ambient light or functional lighting?
Ambience comes from a flux directed toward the facade or the foliage, never toward the eyes. Functional light follows the route: steps, threshold, table surface. Two separate circuits, or two different orientations, allow lighting only one of them depending on the moment.
Colour temperature: which white for a terrace?
Around 2700 to 3000 K, warm white relaxes the space and suits meals. Around 3500 to 4000 K, neutral white renders colours more faithfully and makes a staircase safer. It is better to keep the same white family across the whole area. Indoors, the modern style lamps for the living room follow the same logic of consistency.
How to wire several lamps on a single electrical supply?
Several lamps can be connected to the same supply if the circuit allows it. They are wired in parallel, each receiving the live and neutral, then the conductor cross-section and circuit protection are checked. Switching off the power and having the diagram approved by an electrician remains the rule.
Wiring 3 lamps to 1 switch: which diagram?
The supply feeds the switch; the switched live goes back to each light, while the neutral joins them directly. The three points come on together and stay independent if one fails. Each connection is made in an accessible box, suited to outdoors, with the power off.
Wiring several lamps in parallel: the checkpoints
Check the total load, the conductor cross-section, the dedicated protection and the sealing of the boxes. An outdoor circuit requires residual current protection and neat cable entries. The metal lights remind us of the importance of a properly connected earth on metal bodies.
How to install recessed spots in a ceiling or soffit?
Installation starts by locating the joists and conduits, then by drilling a pilot hole suited to the housing. The spot is wired with the power off, fixed by spring or screw depending on the model, and adjusted before commissioning. Outdoors, the sealing of the cable entry is checked.
How to arrange ceiling spots?
Arrange them by zone to be lit, not at a regular rhythm: near the table, along the walkway, toward the facade. Avoid the line of sight when seated and positions that cast a guest's shadow on the table. Marking with tape before drilling validates the positions.
How to locate the position before drilling?
Locate joists, conduits and water supplies, then check the available thickness above the ceiling or soffit. Drill a pilot hole smaller than the housing. Indoors, the design lamps for the living room and the white versions are installed using the same locating logic.
Outdoor E27 bulb: how to choose the right source?
An outdoor E27 bulb must be intended for outdoor use and compatible with the light. Check the socket, the voltage, the colour temperature and the IP rating of the assembly. An integrated LED avoids replacement, while an E27 socket allows the source to be changed if the light accepts it.
E27 socket, GU10 or integrated LED: what to choose?
The E27 socket offers a replaceable source and a wide choice of temperatures. The GU10, more compact, suits adjustable spots. The integrated LED simplifies maintenance but makes the light inseparable from its source. Always check compatibility on the model sheet, never by deduction.
Outdoor E27 bulb: checks before buying
Check the stated outdoor use, the voltage, the colour temperature and the IP rating of the light that houses it. A watertight bulb in a housing that is not protects nothing. The LED lamps for the bedroom illustrate the same vigilance about the source.
| Source | Socket | Advantage | To check |
|---|---|---|---|
| Integrated LED | No socket | No lamp replacement | Replacing the light in case of failure |
| E27 bulb | E27 | Replaceable source | Outdoor use and compatibility |
| GU10 spot | GU10 | Can be adjusted | Fixing and IP rating of the light |
| Remote LED module | Depending on model | Hidden source | Access to the driver and connection |
Which material and style for an outdoor recessed light?
The visible material of an outdoor recessed light determines its look and durability: stainless steel, aluminium or brass for the trim, glass for diffusion. Style is chosen according to the facade and the ground, while the discretion of a recessed light depends on its flush finish and its colour.
Stainless steel, aluminium or brass: what is the difference?
Stainless steel withstands exposure and stays understated on a stone terrace. Aluminium, lighter, suits slim trims and matt shades. Brass patinates and warms an old facade. Tempered glass protects the source and lets the beam through; its cleanliness determines the sharpness of the rendering.
Discreet recess or deliberate light signal?
A flush trim in the colour of the ground blends away: this is the choice for a path. A visible metal ring, or a slightly protruding glass, asserts the signal and accompanies an entrance. For harmony of materials indoors, compare the ceramic lamps, the design wood lamps and the Nordic lamps.
How to maintain and make outdoor recessed lighting last?
An outdoor recessed light stays legible by cleaning the glass with a soft cloth and removing leaves and soil around the housing. Check the seal, the water drainage and the tightness of the screws. A sealing defect is dealt with before condensation or corrosion appears.
How to clean a recessed light without damaging it?
Switch off the circuit, wipe the glass with clean water and a non-abrasive cloth, without aggressive products on the seal. Remove debris from the cup: water that stagnates eventually forces the seal. Check the tightness of the screws and the condition of the cable gland at the same time.
Mistakes to avoid during installation
Installing an indoor model outside, drowning the housing in a puddle, aiming the beam toward the neighbour's window, forgetting access above the ceiling: these are the recurring faults. Also plan for replacing the source from the design stage. The complete guide remains all our lights, to consult before ordering.
Before choosing, check the type of recess, the IP rating and the light source. Compare the adjustable models and the design lamps for the office if your project also involves indoors.
To light a facade or a tree, a ground recessed floodlight with a wide beam requires a higher wattage than simple waymarking.
The questions most often asked about installation and wiring, in short answers:
Wiring 3 lamps to 1 switch: how to do it?
The three lamps are wired in parallel behind the same switch: the supply feeds the switch, then the switched live goes back to each lamp, while the neutral joins them directly. The circuit must remain protected and accessible. An electrician checks the cross-section, the connections and the load before powering up.
Can several lamps be wired in parallel?
Yes, parallel wiring is the usual solution: each light receives the same voltage and remains independent of the others. However, the circuit, the switch and the protection must support the whole. Connections are made with the power off, in accessible boxes suited to outdoors.
Outdoor wall light for a terrace: how to integrate it?
Place it near the entrance, under an awning or along a wall, in a spot that does not dazzle the guests. It complements a ground or ceiling recessed light. Check the fixing to the substrate, the sealing and the cable routing before installation.
How to arrange ceiling spots?
Spots are arranged according to the zones to be lit, not at a regular rhythm: near the table, along the walkway and toward the facade. Avoid placing a spot in the line of sight and keep the light even. A trial before drilling helps validate the positions.
Outdoor E27 bulb: how to choose it?
It must be compatible with the light and intended for outdoor use. Check the socket, the voltage, the colour temperature and the IP rating of the assembly. An integrated LED avoids replacement, an E27 socket allows the source to be changed if the light accepts it.





