120 cm fluorescent tube
This selection is also available in our French store: Tube néon 120 cm
No products in this selection.
- Tracked delivery to your country Tracked delivery
- Secure payment at checkout Multiple payment methods
- 14 days to change your mind 14-day returns
- Secure payment Secure payment
Not sure of your style? Find it in 30 seconds
A few questions, and we will show you the pieces made for you.
Frequently asked questions
How do I choose the right product?
What are the delivery times?
Can I return an item?
Can I pay in instalments?

An interior that reflects who you are
Carefully selected pieces, shipped from our warehouses. Our team advises you before you buy, so you choose with confidence.
- Tracked delivery
- Pay in instalments, where available
- 14 days to change your mind
- Advice & showroom in Lyon, France
A 1.20 m tube is bought on three measurements: the overall length including pins, the tube diameter (T5 or T8) and the type of sockets on the luminaire. Note these three values before ordering, they decide compatibility, the quality of light and how easy the replacement will be.
What light does a 120cm neon tube give and which room should it go in?
A 1.20 m tube spreads an even linear light along its whole length, with no hot spot or shadow area. That is what makes it effective above a worktop, a workbench or along a bathroom wall, where a point light would leave dark zones.
The light of a 1.20 m tube above a worktop
Laid flat under a wall unit or in a strip fixed to the wall, the tube lights the worktop evenly along its whole length. Hands and utensils no longer cast a shadow on the chopping board. Placed close to a wall, it reveals the texture of the surface and visually enlarges a narrow hallway.
The rooms where a 120cm tube finds its place
The kitchen and its worktop, the garage and the workshop to see under a bonnet, the bathroom above the mirror, the hallway and the storeroom. In a damp room, the protection of the luminaire matters as much as the tube: see the waterproof LED tubes for damp rooms and the bathroom lighting. For a shed or a covered terrace, move on to the outdoor LED tubes.
What is the difference between T5 and T8 neon tubes?
The T8 is the most widespread tube: it equips most old strips and ceiling lights, with wide sockets. The T5 is slimmer and fits in compact or closed luminaires; at equal length, it needs a specific holder. The format is read on the length of the tube and on the sockets of the luminaire.
The T8, format of old strips and ceiling lights
A 120cm T8 fluorescent tube slips into the wide sockets of a standard strip, a quarter turn to lock. It is the format still found in kitchens from the 2000s and in garages. Replacing it with a T8 LED tube is the easiest to source: see our LED tubes range.
The T5, slimmer, for compact and closed luminaires
The T5 fits in a shallow box, under a glazed cabinet or in a closed wall light, where a T8 does not fit. It requires G5 sockets and a dedicated holder: a T5 tube never fits in a T8 strip. For a complete luminaire, compare the shapes in the Designix luminaire catalogue.
| Criterion | T5 tube | T8 tube |
|---|---|---|
| Size | The slimmer of the two | The wider, historic format |
| Sockets | Dedicated holder, often built into the luminaire | Wide sockets on a standard strip |
| 120 cm length | Exists in both formats | Common format of ceiling lights and strips |
| Switch to LED | Dedicated T5 LED tube | T8 LED tube, the easiest to find |
| Where to find it | Closed luminaire, glazed cabinet | Kitchen, garage, workshop, storeroom |
How to measure the length of a 120cm neon tube before ordering?
Measure the tube overall, pins included, then compare with the inner length of the strip. A 120 cm tube fits on a holder designed for that length: also check the distance between the sockets and the accepted diameter, otherwise the tube does not fit or does not line up.
Measure the tube overall, pins included
Remove the tube and place the tape from one end of a pin to the other, not on the glass part alone. The commercial dimension matches this overall measurement. An old-model neon tube may show the same length with a different diameter, hence checking T5 or T8 before confirming the basket.
Check the length of the strip and the distance between the sockets
Then measure the inside of the luminaire and the gap between the two sockets. A tube longer than the strip does not clip in; pins that do not line up give a tube that stays off. The two most frequent errors come from there, and from 1.50 m tubes ordered for a 1.20 m strip.
Is it possible to replace a neon tube with an LED tube?
Yes, in most luminaires, provided you choose an LED tube compatible with the ballast in place or have that ballast removed. Check the length, the sockets and the type of ballast before ordering. If the luminaire is old or cracked, replacing it entirely is often simpler.
What changes: starter, ballast and sockets
The length and sockets stay the same, it is the power supply that changes. A 120cm LED tube designed for a starter holder fits like the old one, once the starter is neutralised. A tube stated as ballast-compatible works on the luminaire left as it is. The gain shows in instant start and lower consumption.
The cases where replacing the luminaire is simpler
A rusted box, a broken reflector, a ballast that hums: in these cases, a new luminaire costs less time than the modification. Look at the 1.20 m LED tubes to keep the holder, or the Designix luminaire catalogue to start from scratch with a tube spotlight rail.
How to change a neon tube on a luminaire with an integrated ballast?
Cut the power at the breaker, then remove the tube with a quarter turn. The integrated ballast is behind the reflector: depending on whether it is magnetic or electronic, the new LED tube will be stated as compatible or will need to be powered directly, with the ballast removed. If in doubt, have the wiring checked.
Cut the power and identify the type of ballast
Cut at the breaker, not just at the switch. Unclip the diffuser, turn the tube a quarter turn and take it out. The ballast is the rectangular block fixed in the box: note the reference written on it and the number of wires leaving it, these two pieces of information are enough to choose the right tube.
When the ballast must be removed for an LED tube
A direct-power tube does not tolerate the ballast: it must be disconnected and the wires repositioned according to the diagram provided, live on one side, neutral on the other. This is an electrician's job if you are not comfortable. Compatible models avoid this step, see switching to an LED tube.
How to fit an LED neon on an old holder and is a starter needed?
On a starter holder, the LED tube designed for this setup fits like the old one, with the starter removed or replaced by the supplied dummy. On an electronic ballast holder, the tube must be stated as compatible. An LED tube that requires a direct power supply does not work on a holder left as it is.
An LED tube on a starter holder: what to remove
The starter is the small cylinder housed on the side of the strip. On an LED tube designed for this setup, it is unscrewed and the supplied dummy takes its place, or it is simply left absent. Leaving an active starter with an unsuitable tube causes flickering or a starting fault.
The wiring diagram of an LED neon tube, in plain terms
Only two cases. Starter holder: nothing to rewire, the tube is replaced. Ballast holder: either a compatible tube fits as it is, or the ballast is removed and the wires repositioned direct. Follow the diagram printed on the tube packaging, it is specific to each model. For a new luminaire, see the black finish tube spotlights.
What do 36 W and 840 mean on a 120cm neon tube?
36 W is the reference power of 1.20 m fluorescent tubes. The code 840 reads in two parts: 8 for the colour rendering index, 40 for a colour temperature of 4000 K, a neutral white light. An LED tube shows its own power, lower at comparable illuminance. To compare, look at the flux in lumens and the lm/W: these two values matter more than the power in watts.
Read the power and the code on the tube label
The label printed on the glass gives the power, the colour code and sometimes the protection index. On a 120cm 36 W neon tube, the power does not tell the quantity of light: it is compared from a fluorescent to an LED only by taking the technology into account. Trust the new tube, not the power of the old one.
830, 840, 865: choosing the colour temperature
A warm white around 3000 K sets up a living room, a neutral white around 4000 K suits work and the kitchen, a cool white around 6500 K serves the garage and storerooms. Keep the same white family in a room, otherwise the difference shows on the walls.
| Code | Temperature | Rendering | Where to use it |
|---|---|---|---|
| 830 | Warm white 3000 K | CRI 80 | Living room, entrance |
| 840 | Neutral white 4000 K | CRI 80 | Kitchen, office, workshop |
| 865 | Cool white 6500 K | CRI 80 | Garage, outdoor, storeroom |
How to choose a wall light with a glass tube?
A glass tube wall light spreads the light upwards and downwards, with a rendering softened by the glass. It is chosen according to the length of the tube it holds, the space available on the wall and the protection index if it is placed in a damp room. The glass is cleaned with soapy water.
The glass tube, for a softened light on the wall
Frosted or ribbed glass breaks the linearity of the tube and spreads the light in a fan on the wall, without dazzling when you walk past. That is what distinguishes a wall light from a bare strip placed in a kitchen. Compare the shapes in the tube wall lights.
Where to place a tube wall light in the house
On either side of a bathroom mirror, above a sideboard, along a hallway or at the head of a bed instead of two lamps. Check the length of the accepted tube before drilling, and the protection index in a wet room. A matching model exists as tube pendants and as tube floor lamps.
How to match a 120 cm tube with the rest of the lighting?
A linear tube goes well with a pendant above the table and a floor lamp in the corner, provided you keep the same white family: neutral for working, warmer for living. Avoid mixing several temperatures in the same room, the eye quickly spots the difference.
Pairing a tube with a pendant or a floor lamp
On a worktop, the tube stays discreet and functional; above the table, a low pendant structures the room. The adjustable tube spotlights take over on a wall, while the Designix luminaire catalogue lets you compose the whole of a room.
The finishes and whites that work together
Check the distance between the fixings and the type of sockets before choosing a 1.20 m tube; in a damp room, take a suitable IP rating. Stick to two temperatures maximum per level, and to one in a small room. See the tubes for kitchen worktops and the garage lighting.
See the 1.20 m LED tubes and choose the right cap
- Secure payment
- Tracked delivery
- Returns
- Designix customer service
Frequently asked questions
What is the wattage of an LED neon tube?
It is shown on the tube and on its packaging, never identical from one model to another. A 1.20 m LED tube consumes far less than a fluorescent tube of the same length for comparable illuminance. It is the tube label, not the power of the old one, that counts after the replacement.
What is the difference between neon and LED?
Neon refers to a gas fluorescent tube, with a ballast and often a starter, whose start takes a few moments. The LED tube uses diodes, starts immediately and consumes less at comparable illuminance. Both fit on holders of the same length, but the LED tube must be compatible with the luminaire ballast.
Is it possible to fit an LED neon on a standard holder?
Yes if the tube is stated as compatible with the holder in place. A luminaire with a starter accepts an LED tube designed for this setup, once the starter is removed. A luminaire with an electronic ballast requires a so-called ballast-compatible tube. Always check the length and the type of sockets before ordering.
How can I replace a fluorescent tube with an LED tube?
Cut the power, remove the old tube with a quarter turn and note the length and the type of sockets. Choose an LED tube of the same length, compatible with the ballast or designed for a direct power supply. Reconnect, switch the breaker back on and check that no flickering appears.
Is a starter needed for an LED tube?
No, an LED tube does not need a starter to work. On a luminaire that has one, the starter is removed or replaced by the dummy supplied with the tube. The starter belongs to the fluorescent setup: leaving it in place with an unsuitable LED tube causes a starting fault.
Can you find a 120cm neon tube that is not LED?
Yes, 1.20 m fluorescent tubes still exist, in T8 in particular, for luminaires that have not been modified. They are chosen according to the length, the sockets and the colour code written on the old tube. Many luminaires switch to LED at the time of replacement.
A 120cm neon tube without a starter, how is it fitted?
A 1.20 m tube without a starter corresponds to a luminaire with an electronic ballast or to an LED tube with a direct power supply. In the first case, the tube fits like the old one. In the second, the ballast is removed and the wires repositioned: have the wiring checked if you are not sure.





