{"title":"R7S table lamps","description":"\u003cp\u003eFirst check the socket spacing on your lamp: 78 mm or 118 mm, and that measurement decides which R7S bulb to buy, not the other way round. Once the length is known, the rest comes down to technology, head orientation and where the fixture actually sits in the room.\u003c\/p\u003e\n\n\u003ch2 id=\"ampoule-r7s-culot\"\u003eWhat is an R7S bulb and why does this base change the choice of your table lamp?\u003c\/h2\u003e\n\u003cp\u003eAn R7S bulb is a linear double-ended bulb: two metal caps at the ends of a glass tube, clipped into two sockets facing each other. It comes in halogen and LED, in two common lengths, 78 mm and 118 mm, which must match the socket spacing of the lamp.\u003c\/p\u003e\n\u003cp\u003eSo you don't choose the bulb before the lamp: you measure the socket gap on the fixture, then buy the tube that fits it. A few millimetres out and the bulb won't hold, or stays too short to engage in the holders. That is why this family is identified by its base before its style. The rest of the catalogue reads the same way, starting from the technical constraint: \u003ca href=\"https:\/\/designix.fr\/collections\/luminaire\"\u003ethe full Designix lighting range\u003c\/a\u003e is then browsed by room and by material.\u003c\/p\u003e\n\n\u003ch3\u003eR7S table lamps 78 mm or 118 mm: which length to choose?\u003c\/h3\u003e\n\u003cp\u003e78 mm suits compact lamps, the ones you place on a bedside table or a small desk. 118 mm goes to wider fixtures, often floor-standing, whose shade diffuses upwards and lights further. In both cases, the measurement that counts is that of the bulb in place, caps included, not the glass tube alone. For a large living room model, compare the \u003ca href=\"\/collections\/lampes-a-poser-design-pour-salon\"\u003edesign table lamps for the living room\u003c\/a\u003e with the measurement to hand.\u003c\/p\u003e\n\n\u003ch3\u003eR7S table lamps LED or halogen: what does it change?\u003c\/h3\u003e\n\u003cp\u003eHalogen gives a warm tint, lights without delay and stays simple to replace, but it heats up and uses more power. LED heats little, uses less and opens up the choice of colour temperatures: around 2700 K for warm light, towards 4000 K for a more neutral rendering. Diode references are found in the \u003ca href=\"\/collections\/lampes-a-poser-led-design\"\u003edesign LED selection\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ctable\u003e\n\u003ccaption\u003eChoosing your R7S bulb according to the lamp and the use\u003c\/caption\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eBase length\u003c\/th\u003e\n\u003cth\u003eTechnology\u003c\/th\u003e\n\u003cth\u003eType of light\u003c\/th\u003e\n\u003cth\u003eRecommended use\u003c\/th\u003e\n\u003cth\u003eGood to know\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e78 mm\u003c\/td\u003e\n\u003ctd\u003eHalogen\u003c\/td\u003e\n\u003ctd\u003eWarm, rather directed\u003c\/td\u003e\n\u003ctd\u003eCompact lamp, reading, accent\u003c\/td\u003e\n\u003ctd\u003eHeats up and should not be touched with bare hands\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e78 mm\u003c\/td\u003e\n\u003ctd\u003eLED\u003c\/td\u003e\n\u003ctd\u003eWhite or warm depending on the reference\u003c\/td\u003e\n\u003ctd\u003eSame use, lower consumption\u003c\/td\u003e\n\u003ctd\u003eCheck compatibility with a dimmer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e118 mm\u003c\/td\u003e\n\u003ctd\u003eHalogen\u003c\/td\u003e\n\u003ctd\u003eWarm, generous\u003c\/td\u003e\n\u003ctd\u003eWide lamp, upward diffusion\u003c\/td\u003e\n\u003ctd\u003eThe lamp must accept a 118 mm base\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e118 mm\u003c\/td\u003e\n\u003ctd\u003eLED\u003c\/td\u003e\n\u003ctd\u003eDepending on the colour temperature chosen\u003c\/td\u003e\n\u003ctd\u003eLarge lamp, ambient lighting\u003c\/td\u003e\n\u003ctd\u003eThe rendering varies from one reference to another\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2 id=\"choisir-lumiere\"\u003eHow to choose your R7S table lamp according to the light you want?\u003c\/h2\u003e\n\u003cp\u003eYou start from the use: reading calls for light directed at the page, atmosphere calls for wider diffusion. Then you check the socket spacing, the space available, the head orientation and the base material, then the wattage and tint of the bulb, without exceeding what the lamp accepts.\u003c\/p\u003e\n\n\u003ch3\u003eWhat bulb wattage for an R7S table lamp?\u003c\/h3\u003e\n\u003cp\u003eThe lamp itself states the maximum wattage allowed, engraved on the socket or on a label under the base: that value is the one that counts. In halogen, wattages climb quickly and the bulb gets hot; in LED, a comparable light output is obtained with far fewer watts. The useful reference remains the lamp, not the bulb: a fixture designed for a modest halogen will not take a more powerful bulb without risk to the holder.\u003c\/p\u003e\n\n\u003ch3\u003eAdjustable table lamps: when should you swivel the light?\u003c\/h3\u003e\n\u003cp\u003eA movable head is useful as soon as one lamp has to cover two situations: lighting a book then tilting towards the wall for atmosphere, aiming at a keyboard then raising the light towards a picture. Models with a ball joint or articulated arm are set once and for all at the right angle. The choice narrows down in the \u003ca href=\"\/collections\/lampes-a-poser-orientables\"\u003eadjustable table lamps\u003c\/a\u003e, and is completed by browsing the \u003ca href=\"\/collections\/luminaire\"\u003elighting catalogue\u003c\/a\u003e by product family.\u003c\/p\u003e\n\n\u003ch2 id=\"ou-installer\"\u003eWhere to place an R7S table lamp in the home?\u003c\/h2\u003e\n\u003cp\u003eIn the living room, it sits near a sofa or in a corner to take the load off the ceiling light; in a bedroom, on the bedside table to read without glare; in the office, next to the screen. A hallway or entrance also benefits from a low lamp that guides your step.\u003c\/p\u003e\n\n\u003ch3\u003eThe most beautiful living room lamps: the criteria that matter\u003c\/h3\u003e\n\u003cp\u003eIn a living room, the height of the base matters as much as the style: a floor-standing lamp should reach shoulder height when seated, to place the light below eye level and not in your eyes. The stability of the base, the length of the cable and access to the switch decide everyday use. The \u003ca href=\"\/collections\/lampes-a-poser-design-pour-chambre\"\u003emodels designed for the bedroom\u003c\/a\u003e follow the same logic, in a smaller format, and the \u003ca href=\"\/collections\/lampes-a-poser-design-pour-bureau\"\u003edesk table lamps\u003c\/a\u003e favour the direction of the beam.\u003c\/p\u003e\n\n\u003ch3\u003eItalian design table lamp, globe lamp or floor lamp: which style for which room?\u003c\/h3\u003e\n\u003cp\u003eThe globe lamp diffuses widely and softens a corner; the floor lamp structures an empty space and occupies the height; the compact model slips onto a narrow piece of furniture. Italian style plays on curve and material, without changing the use: it is chosen for the presence it gives to a corner. For a graphic living room, look at the \u003ca href=\"\/collections\/lampes-a-poser-moderne-pour-salon\"\u003emodern living room lamps\u003c\/a\u003e, and for a softer look, at \u003ca href=\"\/collections\/lampes-a-poser-nordique\"\u003eScandinavian style\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ctable\u003e\n\u003ccaption\u003eWhich R7S table lamp for which room?\u003c\/caption\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eRoom\u003c\/th\u003e\n\u003cth\u003eNeed\u003c\/th\u003e\n\u003cth\u003eLamp format\u003c\/th\u003e\n\u003cth\u003eRecommended base\u003c\/th\u003e\n\u003cth\u003ePoint to watch\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eLiving room\u003c\/td\u003e\n\u003ctd\u003eAtmosphere and reading\u003c\/td\u003e\n\u003ctd\u003eFloor lamp or globe lamp\u003c\/td\u003e\n\u003ctd\u003e118 mm or 78 mm depending on socket spacing\u003c\/td\u003e\n\u003ctd\u003eDo not light the ceiling light zone twice\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBedroom\u003c\/td\u003e\n\u003ctd\u003eSoft light for reading\u003c\/td\u003e\n\u003ctd\u003eSmall bedside lamp\u003c\/td\u003e\n\u003ctd\u003e78 mm in LED\u003c\/td\u003e\n\u003ctd\u003eAvoid light directed at the other occupant\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOffice\u003c\/td\u003e\n\u003ctd\u003eTask lighting\u003c\/td\u003e\n\u003ctd\u003eCompact adjustable lamp\u003c\/td\u003e\n\u003ctd\u003e78 mm\u003c\/td\u003e\n\u003ctd\u003ePlace the source on the opposite side to the writing hand\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEntrance or hallway\u003c\/td\u003e\n\u003ctd\u003eLandmark and welcome\u003c\/td\u003e\n\u003ctd\u003eLow lamp or slim floor lamp\u003c\/td\u003e\n\u003ctd\u003e78 mm in LED\u003c\/td\u003e\n\u003ctd\u003eProvide an easily accessible switch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2 id=\"brancher-plusieurs\"\u003eHow to connect several lamps to a single electrical supply?\u003c\/h2\u003e\n\u003cp\u003eYou start from the existing circuit: each lamp is connected in parallel on the same supply, with a terminal block or connector blocks, respecting the conductor cross-section and the current allowed by the circuit. Power must be switched off, connections tight, earth reconnected if the lamp has one.\u003c\/p\u003e\n\n\u003ch3\u003eConnecting 3 lamps to 1 switch: the logic to follow\u003c\/h3\u003e\n\u003cp\u003eThree lamps controlled together are wired in parallel: the live goes from the switch to each socket, the neutral returns from each socket to the same point. You add up the wattage of the three bulbs before validating, because it is the total that the circuit must withstand. A clean junction box avoids splices and will make a future replacement easier.\u003c\/p\u003e\n\n\u003ch3\u003eConnecting several lamps in parallel: what to check\u003c\/h3\u003e\n\u003cp\u003eCheck the capacity of the terminal block, the tightness of each wire and the presence of the earth when the fixture has one. A two-way switch or an extra switch is planned before installation, not after. At the slightest doubt about the conductor cross-section or the relevant circuit breaker, an electrician validates the assembly: it is the only way to be certain the installation will last.\u003c\/p\u003e\n\n\u003ch2 id=\"spots-plafond\"\u003eHow to arrange ceiling spots with an R7S table lamp?\u003c\/h2\u003e\n\u003cp\u003eThe ceiling provides general lighting, the table lamp brings the accent and the atmosphere. Avoid doubling the same zone: spots are distributed in a ring or in regular lines, the lamp is placed where you need close light, near the sofa, the bed or the desk.\u003c\/p\u003e\n\n\u003ch3\u003eCeiling spots and accent lamp: the distribution that works\u003c\/h3\u003e\n\u003cp\u003eIn practice, you draw two networks: regular points on the ceiling to avoid dark zones, then a low point near the armchair or the screen. The most common mistake is placing a lamp right under a spot already aimed at the same table, which creates two shadows and reflections on a screen. One source per activity zone is enough.\u003c\/p\u003e\n\n\u003ch3\u003eThree lighting modes to combine in a room\u003c\/h3\u003e\n\u003cp\u003eGeneral lighting lights widely and without a strong direction. Task lighting is directed at an activity, reading or working, and calls for a nearby source. Ambient lighting stays softer and highlights a wall or a corner. An R7S table lamp mainly covers the last two, which explains why it complements a ceiling light rather than replacing it. On a workstation, \u003ca href=\"\/collections\/lampes-a-poser-en-metal-pour-bureau\"\u003emetal desk lamps\u003c\/a\u003e are easy to adjust, and \u003ca href=\"\/collections\/lampes-a-poser-led-pour-bureau\"\u003eLED desk lamps\u003c\/a\u003e limit heating above the surface.\u003c\/p\u003e\n\n\u003ch2 id=\"inconvenients-led\"\u003eWhat are the drawbacks of LED lamps and should you choose an LED R7S?\u003c\/h2\u003e\n\u003cp\u003eThe LED R7S heats less and uses less than halogen and lights instantly, but not all references are equal: tint and colour rendering vary, and some do not work with a dimmer. Halogen remains appreciated for its warm tint. The choice depends on the use.\u003c\/p\u003e\n\n\u003ch3\u003eR7S table lamps 200 W: what does this wattage correspond to?\u003c\/h3\u003e\n\u003cp\u003eThe 200 W mention found on some bulbs describes a halogen consumption, not a promise of light output for all technologies. It mainly serves as a replacement reference: at comparable output, an LED needs far fewer watts. What counts remains the maximum wattage allowed by the fixture, and the tint you want to obtain in the room.\u003c\/p\u003e\n\n\u003ch3\u003eDoes an LED R7S work with a dimmer?\u003c\/h3\u003e\n\u003cp\u003eNot systematically. A so-called dimmable LED is controlled with a compatible dimmer, often of the type suited to low loads; a standard LED buzzes, flickers or switches off badly. The safest is to check both instructions, bulb and dimmer, before installing. On a bedside or desk lamp, the non-dimmable version is more than enough and simplifies the assembly, for example in the \u003ca href=\"\/collections\/lampes-a-poser-led-pour-chambre\"\u003eLED table lamps for the bedroom\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2 id=\"changer-entretenir\"\u003eHow to change an R7S bulb and maintain your table lamp?\u003c\/h2\u003e\n\u003cp\u003eSwitch off the power, let it cool, then slightly spread the sockets or unscrew the holders to free the bulb from one end, without forcing. When refitting, the bulb must be aligned and both caps properly engaged. A soft cloth is enough for the base and the shade.\u003c\/p\u003e\n\n\u003ch3\u003eR7S table lamps: mistakes to avoid during assembly\u003c\/h3\u003e\n\u003cp\u003eA halogen bulb should never be touched with bare hands: the grease left on the glass marks the tube when switched on and shortens its lifespan. Also avoid forcing a socket to gain a few millimetres, refitting a bulb crooked, and changing the bulb without having checked the original length. A slightly shorter tube holds badly and ends up slipping out of its holder.\u003c\/p\u003e\n\n\u003ch3\u003eCleaning the base and shade without damaging the finish\u003c\/h3\u003e\n\u003cp\u003eA soft, slightly damp cloth is enough on metal, wood or ceramic. Avoid abrasive products and alcohol on lacquered or gilded finishes, which lose their shine. The fabric of a shade is dusted dry, with a soft brush, and rarely cleaned in depth: moisture marks the fibres and distorts the shape.\u003c\/p\u003e\n\n\u003ch2 id=\"accorder-deco\"\u003eHow to match your R7S table lamp to the decor and the budget?\u003c\/h2\u003e\n\u003cp\u003eFirst choose the family of material and colour that dialogues with the room: metal and black for a graphic interior, wood and linen for a softer look, ceramic and crystal for a more dressed presence. The budget is decided by the finish and the bulb technology chosen.\u003c\/p\u003e\n\n\u003ch3\u003eWood, metal, ceramic, crystal: which material for which effect?\u003c\/h3\u003e\n\u003cp\u003eWood warms a corner and matches natural fibres. Matte black metal disappears in a contemporary interior and leaves only the light visible. Ceramic brings a matte presence and a little relief, crystal plays on transparency and reflections. For a bright living room, \u003ca href=\"\/collections\/lampes-a-poser-en-bois-design\"\u003edesign wood lamps\u003c\/a\u003e fit anywhere; for a more dressed room, look at the \u003ca href=\"\/collections\/lampes-a-poser-en-ceramique\"\u003eceramic lamps\u003c\/a\u003e then the \u003ca href=\"\/collections\/lampes-a-poser-en-cristal\"\u003ecrystal pieces\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eBlack, white or gold: how to decide?\u003c\/h3\u003e\n\u003cp\u003eBlack structures and stands out on a light wall, white fades and lets the shade lead, gold warms a dimly lit room. One accent is enough: several metal pieces in different tints in the same room cancel each other out. A fabric shade, like \u003ca href=\"\/collections\/lampes-a-poser-en-lin\"\u003elinen shades\u003c\/a\u003e, tempers a metal base and softens the light upwards. In a dark living room, \u003ca href=\"\/collections\/lampes-a-poser-coloris-noir-pour-salon\"\u003eblack finishes for the living room\u003c\/a\u003e blend into the decor and let the beam do the work.\u003c\/p\u003e\n\n\u003cp\u003eSecure payment, tracked delivery, returns and Designix customer service: you order the lamp and its bulb in the same place, and customer service answers on base compatibility if any doubt remains. Measure your sockets, choose the technology, then validate your model.\u003c\/p\u003e\n\n\u003ch2 id=\"faq\"\u003eFrequently asked questions about R7S table lamps\u003c\/h2\u003e\n\u003cdetails\u003e\n\u003csummary\u003eWhat is an R7S bulb?\u003c\/summary\u003e\n\u003cp\u003eIt is a linear double-ended bulb, made of a glass tube finished with two metal caps. It clips between two sockets placed facing each other in the lamp. It comes in a halogen version and an LED version, in 78 mm and 118 mm.\u003c\/p\u003e\n\u003c\/details\u003e\n\u003cdetails\u003e\n\u003csummary\u003eWhat is the size of an R7S halogen bulb?\u003c\/summary\u003e\n\u003cp\u003eThe two most common lengths are 78 mm and 118 mm, measured between the two caps. This is not a detail: the length must match the socket spacing of the lamp. If in doubt, measure the old bulb before ordering.\u003c\/p\u003e\n\u003c\/details\u003e\n\u003cdetails\u003e\n\u003csummary\u003eWhat are the drawbacks of LED lamps?\u003c\/summary\u003e\n\u003cp\u003eAn LED heats little and uses less, but not all are equal: colour rendering and tint vary from one reference to another, some do not work with a dimmer, and the purchase price often remains higher than that of the equivalent halogen.\u003c\/p\u003e\n\u003c\/details\u003e\n\u003cdetails\u003e\n\u003csummary\u003eWhich is the most efficient lamp?\u003c\/summary\u003e\n\u003cp\u003eIn terms of consumption, LED is the most efficient technology: it converts more electricity into light and less into heat than halogen. The most efficient lamp remains the one whose base, orientation and diffusion match the actual use of the room.\u003c\/p\u003e\n\u003c\/details\u003e\n\u003cdetails\u003e\n\u003csummary\u003eWhat are the 4 types of lamps?\u003c\/summary\u003e\n\u003cp\u003eIn lighting, the families are often grouped as follows: pendants, ceiling lights and wall lights, table lamps and floor lamps. Table lamps are distinguished by their base, such as R7S, and by their use: bedside, desk or reading corner.\u003c\/p\u003e\n\u003c\/details\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"CollectionPage\",\"name\":\"R7S table lamps: the guide to choosing your lamp and bulb\",\"description\":\"Understand the R7S base, choose between 78 and 118 mm, LED or halogen, then find the table lamp that truly lights living room, bedroom and office.\",\"url\":\"https:\/\/designix.fr\/collections\/lampes-a-poser-r7s\",\"isPartOf\":{\"@type\":\"WebSite\",\"name\":\"Designix\",\"url\":\"https:\/\/designix.fr\"},\"speakable\":{\"@type\":\"SpeakableSpecification\",\"cssSelector\":[\"h1\",\"h2\"]}},{\"@type\":\"BreadcrumbList\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/designix.fr\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Lighting\",\"item\":\"https:\/\/designix.fr\/collections\/luminaire\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Lamps\",\"item\":\"https:\/\/designix.fr\/collections\/lampes\"},{\"@type\":\"ListItem\",\"position\":4,\"name\":\"R7S table lamps: the guide to choosing your lamp and bulb\",\"item\":\"https:\/\/designix.fr\/collections\/lampes-a-poser-r7s\"}]},{\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"What is an R7S bulb?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"It is a linear double-ended bulb, made of a glass tube finished with two metal caps. It clips between two sockets placed facing each other in the lamp. It comes in a halogen version and an LED version, in 78 mm and 118 mm.\"}},{\"@type\":\"Question\",\"name\":\"What is the size of an R7S halogen bulb?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"The two most common lengths are 78 mm and 118 mm, measured between the two caps. This is not a detail: the length must match the socket spacing of the lamp. If in doubt, measure the old bulb before ordering.\"}},{\"@type\":\"Question\",\"name\":\"What are the drawbacks of LED lamps?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"An LED heats little and uses less, but not all are equal: colour rendering and tint vary from one reference to another, some do not work with a dimmer, and the purchase price often remains higher than that of the equivalent halogen.\"}},{\"@type\":\"Question\",\"name\":\"Which is the most efficient lamp?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"In terms of consumption, LED is the most efficient technology: it converts more electricity into light and less into heat than halogen. The most efficient lamp remains the one whose base, orientation and diffusion match the actual use of the room.\"}},{\"@type\":\"Question\",\"name\":\"What are the 3 lighting modes?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"A distinction is made between general lighting, which lights the whole room, task lighting, directed at an activity such as reading or working, and ambient lighting, softer, which highlights a wall or a corner. An R7S table lamp mainly serves the last two.\"}},{\"@type\":\"Question\",\"name\":\"What are the 4 types of lamps?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"In lighting, the families are often grouped as follows: pendants, ceiling lights and wall lights, table lamps and floor lamps. Table lamps are distinguished by their base, such as R7S, and by their use: bedside, desk or reading corner.\"}},{\"@type\":\"Question\",\"name\":\"How to connect several lamps in parallel?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Each lamp is connected to the same conductors, live, neutral and earth, in parallel, with a terminal block suited to the number of wires. Switch off the power, check the current allowed by the circuit and tighten each connection. If in doubt, an electrician validates the assembly.\"}}]}]}\u003c\/script\u003e","products":[],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0677\/8598\/2228\/collections\/designix-entete-lampes-a-poser-r7s-v1.jpg?v=1792646968","url":"https:\/\/designix-lighting.com\/collections\/r7s-table-lamps.oembed","provider":"Designix","version":"1.0","type":"link"}