{"title":"12V waterproof LED strips","description":"\u003cp\u003eA 12V waterproof LED strip installs where a standard light fitting cannot go: under a boat's swim platform, along a van's running board, in a bathroom, on a covered terrace. The low voltage removes the risk on contact and the coating blocks moisture, provided you also protect the connections and provide a 12V transformer.\u003c\/p\u003e\n\n\u003ch2 id=\"definition\"\u003eWhat is a 12V waterproof LED strip and what does low voltage change?\u003c\/h2\u003e\n\u003cp\u003eA 12V waterproof LED strip is a flexible band of LEDs, powered at low voltage, protected by a coating against moisture and splashes. 12V is not a fad: it is the onboard voltage of vehicles and a level that is safe to touch. This constraint requires a transformer or driver that steps down the 230 V mains supply to 12 V.\u003c\/p\u003e\n\n\u003ch3\u003e12V low voltage: what it changes for installation\u003c\/h3\u003e\n\u003cp\u003eThe strip can be installed without contact safety precautions, which opens up wet areas and vehicles, but moves the tricky point to the power supply. The driver remains a device to be plugged into the mains: it must be ventilated, accessible for servicing and placed away from water. Voltage drop also comes into play, more noticeable at 12V than at mains voltage, which shifts the trade-off towards \u003ca href=\"https:\/\/designix.fr\/collections\/rubans-led-24v\"\u003eswitching to 24 volts for long runs\u003c\/a\u003e when the route gets longer.\u003c\/p\u003e\n\n\u003ch3\u003eRuban or bande LED: is it the same thing?\u003c\/h3\u003e\n\u003cp\u003eBoth words refer to the same product: a flexible circuit board carrying SMD LEDs, cuttable in groups. The term bande emphasises the flat, continuous shape, the term ruban the flexibility of the backing. Choose a silicone coating if you want a smooth surface that is easy to clean, a polyurethane sheath if the strip must withstand rubbing. To compare the variants, see \u003ca href=\"\/collections\/rubans-led\"\u003ethe full range of LED strips\u003c\/a\u003e and \u003ca href=\"\/collections\/rubans-led-etanches\"\u003eall our waterproof LED strips\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2 id=\"lieux\"\u003eWhere to install a 12V waterproof LED strip: outdoors, boat, van or car?\u003c\/h2\u003e\n\u003cp\u003e12V waterproof is suitable for wet rooms and vehicles: bathroom, covered terrace, boat swim platform, van ceiling, car boot, motorcycle fairings. Avoid immersion unless rated IP68, and protect the connectors, the weak point of any outdoor installation.\u003c\/p\u003e\n\n\u003ch3\u003e12V waterproof outdoor LED strip\u003c\/h3\u003e\n\u003cp\u003eOn a covered terrace or under a canopy, the strip highlights a step, a pergola or the edge of a bar without glare. Indirect light tucked under a piece of furniture is easier on the eyes than a spotlight facing you. Technically, water always runs down through the connection: sheath every junction, point the plugs downwards and avoid junctions that form a bowl. For a pond, turn to \u003ca href=\"\/collections\/rubans-led-pour-piscine\"\u003epond and pool lighting\u003c\/a\u003e, which requires immersion protection.\u003c\/p\u003e\n\n\u003ch3\u003e12V waterproof LED strip for boats\u003c\/h3\u003e\n\u003cp\u003eOn a boat, the low voltage matches the onboard supply and condensation is constant. A strip fitted under the foredeck or in the cockpit lights the deck without switching on the mast spotlight, which preserves night vision. Fix the strip to a rigid support rather than directly to the deck, and protect the connections with heat-shrink tubing or a sleeve, as they are the first to fail with spray and vibration.\u003c\/p\u003e\n\n\u003ch3\u003e12V waterproof LED strip for cars and motorcycles\u003c\/h3\u003e\n\u003cp\u003eIn a boot, under a running board or along a motorcycle fairing, the waterproof strip lights the useful area and goes unnoticed whether on or off. The real constraint is mechanical: rubbing, vibration, washing jets. Choose a sheathed strip, a connection to a fused circuit, and bear in mind that decorative lighting does not replace an approved signalling light. A flexible, discreet model is often chosen for \u003ca href=\"\/collections\/rubans-led-pour-salon\"\u003eambient strips for the living room\u003c\/a\u003e as much as for a vehicle interior.\u003c\/p\u003e\n\n\u003ch2 id=\"ip\"\u003eWhich IP rating to choose for a waterproof LED strip?\u003c\/h2\u003e\n\u003cp\u003eThe IP rating is read in two digits: the first concerns dust, the second water. IP20 does not protect against moisture, IP44 withstands splashes, IP65 jets, IP68 prolonged immersion. A strip installed outdoors or in a bathroom must display at least IP65.\u003c\/p\u003e\n\n\u003ch3\u003eIP65 or IP68: which to choose?\u003c\/h3\u003e\n\u003cp\u003eIP65 covers water jets and rain, so a terrace, a shelter, a cockpit, a van ceiling. IP68 adds immersion, which concerns a pond, a fountain or a submerged fitting. In all cases, the strip's protection covers neither the connector nor the driver: an IP68 strip connected with a bare splice loses its waterproofing in the first storm. So count the strip, the connections and the power supply as three elements to protect separately.\u003c\/p\u003e\n\n\u003ch3\u003eIs IP44 enough in a bathroom?\u003c\/h3\u003e\n\u003cp\u003eIn a wet room, IP44 is suitable outside the shower zone, for a strip fitted under a vanity unit or behind a mirror. Near the bathtub or exposed to direct splashes, go up a level. The right reflex is to check the manufacturer's installation instructions for the permitted zone. To broaden the field, compare with \u003ca href=\"\/collections\/rubans-led-etanches\"\u003ewaterproof LED strip for outdoor use\u003c\/a\u003e before deciding.\u003c\/p\u003e\n\n\u003ctable\u003e\n\u003ccaption\u003eWhich IP rating for which use\u003c\/caption\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eRating\u003c\/th\u003e\n\u003cth\u003eActual protection\u003c\/th\u003e\n\u003cth\u003eWhere to install it\u003c\/th\u003e\n\u003cth\u003eWatch out for\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eIP20\u003c\/td\u003e\n\u003ctd\u003eno protection against water\u003c\/td\u003e\n\u003ctd\u003edry interior, furniture, ceiling\u003c\/td\u003e\n\u003ctd\u003eavoid in wet rooms\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIP44\u003c\/td\u003e\n\u003ctd\u003ewater splashes\u003c\/td\u003e\n\u003ctd\u003ebathroom outside the shower zone\u003c\/td\u003e\n\u003ctd\u003eno direct jets\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIP65\u003c\/td\u003e\n\u003ctd\u003ewater jets\u003c\/td\u003e\n\u003ctd\u003eterrace, shelter, van, boat\u003c\/td\u003e\n\u003ctd\u003ealso protect the connectors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eIP68\u003c\/td\u003e\n\u003ctd\u003eprolonged immersion\u003c\/td\u003e\n\u003ctd\u003epond, fountain, pool\u003c\/td\u003e\n\u003ctd\u003echeck the permitted depth\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2 id=\"tension\"\u003e12V, 24V or 220V LED strip: how to decide?\u003c\/h2\u003e\n\u003cp\u003e12V is the most common voltage for vehicles and short lengths. 24V limits voltage drop and allows longer runs with the same cable gauge. 220V plugs directly into the mains, without a transformer, but is reserved for long lengths and fixed installation.\u003c\/p\u003e\n\n\u003ch3\u003e12V waterproof 24V LED strip 12 metres: how far can you go?\u003c\/h3\u003e\n\u003cp\u003eDoubling the voltage halves the current at equal power, and therefore the loss in the cable. That is why long continuous runs switch to 24V: the end keeps the same intensity as the start, without progressive yellowing. On a very long 12V run, you instead re-power the strip by tapping the driver in the middle of the route. Choosing the cable matters as much as choosing the strip: undersized, it heats up and dims the light.\u003c\/p\u003e\n\n\u003ch3\u003e220V waterproof LED strip or 12V with a transformer?\u003c\/h3\u003e\n\u003cp\u003e220V avoids the driver and suits a cornice or a facade in fixed installation, with more demanding installation safety since you are handling mains voltage. 12V remains more flexible for a removable or mobile setup. Compare \u003ca href=\"\/collections\/rubans-led-220v\"\u003e220V strips without a transformer\u003c\/a\u003e and \u003ca href=\"\/collections\/rubans-led\"\u003eflexible cuttable LED strips\u003c\/a\u003e depending on whether the installation is fixed or not.\u003c\/p\u003e\n\n\u003ctable\u003e\n\u003ccaption\u003e12V, 24V or 220V: which waterproof strip for which project\u003c\/caption\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eCriterion\u003c\/th\u003e\n\u003cth\u003e12V strip\u003c\/th\u003e\n\u003cth\u003e24V strip\u003c\/th\u003e\n\u003cth\u003e220V strip\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower supply\u003c\/td\u003e\n\u003ctd\u003e12V transformer or driver required\u003c\/td\u003e\n\u003ctd\u003e24V driver required\u003c\/td\u003e\n\u003ctd\u003edirect connection to the mains\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVoltage drop\u003c\/td\u003e\n\u003ctd\u003enoticeable over long lengths\u003c\/td\u003e\n\u003ctd\u003eless noticeable, longer runs\u003c\/td\u003e\n\u003ctd\u003elow, long runs possible\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable gauge\u003c\/td\u003e\n\u003ctd\u003elarger at equal power\u003c\/td\u003e\n\u003ctd\u003esmaller at equal power\u003c\/td\u003e\n\u003ctd\u003eno low-voltage cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTypical uses\u003c\/td\u003e\n\u003ctd\u003evan, boat, car, motorcycle, small rooms\u003c\/td\u003e\n\u003ctd\u003elarge rooms, ceilings, continuous runs\u003c\/td\u003e\n\u003ctd\u003ecornices, facades, fixed installation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSafety on contact\u003c\/td\u003e\n\u003ctd\u003elow voltage\u003c\/td\u003e\n\u003ctd\u003elow voltage\u003c\/td\u003e\n\u003ctd\u003emains voltage, careful installation required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2 id=\"couleur\"\u003eRed, blue, RGB or warm white LED strip: which light colour?\u003c\/h2\u003e\n\u003cp\u003eWarm white 2700 K gives a light close to the filament bulb, 3000 K stays warm but crisper, 4000 K leans towards neutral white. RGB versions combine several colours, RGBW adds a dedicated white to light without going through a mix.\u003c\/p\u003e\n\n\u003ch3\u003e12V waterproof red LED strip\u003c\/h3\u003e\n\u003cp\u003eRed highlights a line, a running board or a platform without lighting the area: useful where you want to see without losing night vision, on a boat or in a van. The result remains decorative, it does not replace working lighting. Red tires the eyes quickly if used as the main light in a living room.\u003c\/p\u003e\n\n\u003ch3\u003e12V waterproof blue LED strip\u003c\/h3\u003e\n\u003cp\u003eBlue creates a cool atmosphere, often chosen for a pond edge or a decorative niche. Its short wavelength lights surfaces poorly, which makes it an accent rather than a useful source. Check that the shade is truly monochrome and not an RGB set to blue, as the result differs.\u003c\/p\u003e\n\n\u003ch3\u003eRGB or RGBW: what difference for a living room?\u003c\/h3\u003e\n\u003cp\u003eAn RGB strip mixes three colours to recreate white, with an often greenish result. RGBW adds a dedicated white LED: you keep clean white for reading or dining, and colour for atmosphere. In a living room, this versatility avoids installing two strips. To choose a fixed shade rather than animation, see \u003ca href=\"\/collections\/rubans-led-3000k\"\u003ewarm white 3000 K\u003c\/a\u003e or \u003ca href=\"\/collections\/rubans-led-2700k\"\u003every warm light at 2700 K\u003c\/a\u003e, and for colour, compare \u003ca href=\"\/collections\/rubans-led-rgb\"\u003emulticolour RGB strips\u003c\/a\u003e and \u003ca href=\"\/collections\/rubans-led-rgbw\"\u003eRGBW models with dedicated white\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ctable\u003e\n\u003ccaption\u003eWhite colour and room atmosphere\u003c\/caption\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eTemperature\u003c\/th\u003e\n\u003cth\u003eResult\u003c\/th\u003e\n\u003cth\u003eRecommended room\u003c\/th\u003e\n\u003cth\u003eGood to know\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2700 K\u003c\/td\u003e\n\u003ctd\u003every warm white, amber tint\u003c\/td\u003e\n\u003ctd\u003eliving room, bedroom, reading corner\u003c\/td\u003e\n\u003ctd\u003esofter, less crisp result\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3000 K\u003c\/td\u003e\n\u003ctd\u003ewarm white\u003c\/td\u003e\n\u003ctd\u003ekitchen, dining room, living room\u003c\/td\u003e\n\u003ctd\u003ethe most common indoors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4000 K\u003c\/td\u003e\n\u003ctd\u003eneutral white\u003c\/td\u003e\n\u003ctd\u003eworkshop, garage, worktop\u003c\/td\u003e\n\u003ctd\u003ecooler, less enveloping\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRGB \/ RGBW\u003c\/td\u003e\n\u003ctd\u003ecolours, plus a dedicated white in RGBW\u003c\/td\u003e\n\u003ctd\u003eatmosphere, terrace, headboard\u003c\/td\u003e\n\u003ctd\u003erequires a controller or remote control\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2 id=\"recoupe\"\u003eCuttable LED strip: how does it work?\u003c\/h2\u003e\n\u003cp\u003eA cuttable strip has cut marks every few LEDs, generally in groups of three. You only cut on these marks, never between two LEDs. Then you re-power the section or tap the supply so that the next section keeps the same intensity.\u003c\/p\u003e\n\n\u003ch3\u003eWhere to cut an LED strip without damaging it?\u003c\/h3\u003e\n\u003cp\u003eThe marks form small lines or a pair of copper pads between two groups of LEDs. Cutting in the middle of a group switches off part of the strip and leaves the circuit open. Locate the mark before measuring, never after.\u003c\/p\u003e\n\n\u003ch3\u003eWhat to do with the rest of the strip?\u003c\/h3\u003e\n\u003cp\u003eThe separated section can be reused if it is re-powered: you need to bring 12V to the designated pads, with a waterproof connector, a clamp connector or a solder joint protected by a sheath. A leftover strip without power does not light up through contact with the working part. For sections to be continued over large rooms, look at \u003ca href=\"\/collections\/rubans-led-24v\"\u003eswitching to 24 volts for long runs\u003c\/a\u003e and \u003ca href=\"\/collections\/rubans-led-etanches\"\u003eour waterproof LED strips\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2 id=\"pose\"\u003eHow to install and maintain a 12V waterproof LED strip?\u003c\/h2\u003e\n\u003cp\u003eClean and degrease the surface before sticking, add an aluminium profile to dissipate heat and protect the connections with a sheath or sleeve. Maintenance is limited to a damp cloth, without solvent, and a check of exposed connectors once a year.\u003c\/p\u003e\n\n\u003ch3\u003eHow to fix an LED strip to a damp surface?\u003c\/h3\u003e\n\u003cp\u003eOn a cold, greasy or porous surface, the original adhesive holds poorly. Degrease with alcohol, let it dry, then fit an aluminium profile or a plastic rail and stick the strip to it. The profile serves twice: it presses the strip flat and dissipates heat, which prevents the LEDs from ageing too quickly. Finish with a dab of glue at the ends and a cable gland for the exit.\u003c\/p\u003e\n\n\u003ch3\u003eCleaning an outdoor LED strip without damaging it\u003c\/h3\u003e\n\u003cp\u003eA damp cloth is enough, without solvent or pressure washer, which would force water into the junctions. Check the condition of the sheaths once a year and tighten the connections. To go further on the power supply, see \u003ca href=\"\/collections\/luminaire\"\u003eour lighting catalogue\u003c\/a\u003e and its accessories.\u003c\/p\u003e\n\n\u003ch2 id=\"trouver\"\u003eWhere can I find a waterproof LED lighting strip?\u003c\/h2\u003e\n\u003cp\u003e12V waterproof LED strips are available in DIY stores, from a lighting specialist or online. The sorting criterion remains the IP rating, the voltage and the white colour: this is what distinguishes a strip genuinely intended for outdoor use from an indoor strip simply sold with a housing.\u003c\/p\u003e\n\n\u003ch3\u003e12V waterproof LED strip in store or online?\u003c\/h3\u003e\n\u003cp\u003eA store lets you touch the coating and check the thickness of the sheath. Online, read the technical data sheet rather than the listing title: IP, voltage, LED type, white temperature. For a specific project, start from \u003ca href=\"\/collections\/rubans-led\"\u003ethe full range of LED strips\u003c\/a\u003e and \u003ca href=\"\/collections\/luminaire\"\u003eall our lighting collections\u003c\/a\u003e, then refine by use.\u003c\/p\u003e\n\n\u003ch3\u003eHow to check waterproofing before buying?\u003c\/h3\u003e\n\u003cp\u003eLook for the IP rating stated in black and white, the mention of the coating (silicone, sheath) and the presence of a waterproof connector in the kit. A strip advertised as outdoor without a clear IP offers no guarantee. Also check that the driver is intended for the location, as a bare power supply does not withstand water. Find the suitable models in \u003ca href=\"\/collections\/rubans-led-etanches\"\u003ewaterproof LED strip for outdoor use\u003c\/a\u003e and, for indoor decorative use, \u003ca href=\"\/collections\/rubans-led-pour-salon\"\u003eliving room lighting ideas\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cp\u003eThe choice comes down to three facts that are easy to check before ordering: an IP rating of at least IP65 for outdoor use, a voltage suited to your power supply, and a white colour set according to the room. Once these criteria are set, the rest (length, connections, profile) is sorted out at installation. Browse \u003ca href=\"\/collections\/rubans-led-etanches\"\u003eall our waterproof LED strips\u003c\/a\u003e and \u003ca href=\"\/collections\/luminaire\"\u003eall our light fittings\u003c\/a\u003e to find the strip that suits you.\u003c\/p\u003e\n\n\u003cp\u003eSecure payment, tracked delivery, returns and Designix customer service: you order with peace of mind and can ask your technical questions before connecting.\u003c\/p\u003e\n\n\u003ch2 id=\"faq\"\u003eFrequently asked questions\u003c\/h2\u003e\n\n\u003cdetails\u003e\u003csummary\u003eWhere can I find a waterproof LED lighting strip?\u003c\/summary\u003e\u003cp\u003eIn DIY stores, from a lighting specialist or online. In all cases, sort by three facts printed on the packaging: the IP rating, the supply voltage and the white colour. A strip sold without a clear IP rating is not an outdoor strip.\u003c\/p\u003e\u003c\/details\u003e\n\n\u003cdetails\u003e\u003csummary\u003eWhich LED strip should I choose for outdoor use?\u003c\/summary\u003e\u003cp\u003eA strip with an IP rating of at least IP65, powered at low voltage 12V or 24V for safety, and whose connections are protected as much as the strip itself. Avoid immersion unless rated IP68. The colour is then chosen according to the atmosphere you want on the terrace.\u003c\/p\u003e\u003c\/details\u003e\n\n\u003cdetails\u003e\u003csummary\u003eCuttable LED strip: how does it work?\u003c\/summary\u003e\u003cp\u003eThe strip has spaced cut marks corresponding to groups of LEDs. You only cut on these marks, never in the middle of a group, then re-power the separated section with a suitable connector. Cutting elsewhere damages the circuit and switches off part of the strip.\u003c\/p\u003e\u003c\/details\u003e\n\n\u003cdetails\u003e\u003csummary\u003eCan a 12V waterproof LED strip be installed on a boat or in a van?\u003c\/summary\u003e\u003cp\u003eYes, the 12V low voltage matches the onboard supply, and the waterproof strip withstands condensation and splashes. The fixing must be done carefully to absorb vibration and each connection must be protected. The onboard converter must deliver a stable voltage, without surges.\u003c\/p\u003e\u003c\/details\u003e\n\n\u003cdetails\u003e\u003csummary\u003eDo I need a transformer for a 12V waterproof LED strip?\u003c\/summary\u003e\u003cp\u003eYes, a 12V strip is never connected directly to the mains: you need a transformer or driver that steps down the voltage. This unit must remain accessible, ventilated and protected from water. A strip designed for 230V does without it, but requires a fixed, careful installation.\u003c\/p\u003e\u003c\/details\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"CollectionPage\",\"name\":\"12V waterproof LED strips: the guide to choosing and installing\",\"description\":\"12V waterproof LED strips: understanding the IP rating, voltage drop and installation outdoors, on a boat or in a van. Our advice on choosing and maintenance.\",\"url\":\"https:\/\/designix.fr\/collections\/rubans-led-etanches-12v\",\"isPartOf\":{\"@type\":\"WebSite\",\"name\":\"Designix\",\"url\":\"https:\/\/designix.fr\"},\"speakable\":{\"@type\":\"SpeakableSpecification\",\"cssSelector\":[\"h1\",\"h2\"]}},{\"@type\":\"BreadcrumbList\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/designix.fr\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Lighting\",\"item\":\"https:\/\/designix.fr\/collections\/luminaire\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Strips\",\"item\":\"https:\/\/designix.fr\/collections\/rubans\"},{\"@type\":\"ListItem\",\"position\":4,\"name\":\"12V waterproof LED strips: the guide to choosing and installing\",\"item\":\"https:\/\/designix.fr\/collections\/rubans-led-etanches-12v\"}]},{\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"Where can I find a waterproof LED lighting strip?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"In DIY stores, from a lighting specialist or online. In all cases, sort by three facts printed on the packaging: the IP rating, the supply voltage and the white colour. A strip sold without a clear IP rating is not an outdoor strip.\"}},{\"@type\":\"Question\",\"name\":\"Which LED strip should I choose for outdoor use?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"A strip with an IP rating of at least IP65, powered at low voltage 12V or 24V for safety, and whose connections are protected as much as the strip itself. Avoid immersion unless rated IP68. The colour is then chosen according to the atmosphere you want on the terrace.\"}},{\"@type\":\"Question\",\"name\":\"Cuttable LED strip: how does it work?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"The strip has spaced cut marks corresponding to groups of LEDs. You only cut on these marks, never in the middle of a group, then re-power the separated section with a suitable connector. Cutting elsewhere damages the circuit and switches off part of the strip.\"}},{\"@type\":\"Question\",\"name\":\"Can a 12V waterproof LED strip be installed on a boat or in a van?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes, the 12V low voltage matches the onboard supply, and the waterproof strip withstands condensation and splashes. The fixing must be done carefully to absorb vibration and each connection must be protected. The onboard converter must deliver a stable voltage, without surges.\"}},{\"@type\":\"Question\",\"name\":\"Is a 12V waterproof LED strip suitable for a car or motorcycle?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes, provided you protect the connection and do not expose the strip to direct high-pressure jets or mechanical rubbing. A sheathed strip and a connection to a fused circuit are preferred. Decorative use is distinct from approved signalling lighting.\"}},{\"@type\":\"Question\",\"name\":\"Is there a red or blue 12V waterproof LED strip?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes, single-colour strips are available in red, blue and other shades, with the same waterproof protection as the whites. The coloured result is decorative: it highlights a line, a running board or a platform, but is not intended to light a living room.\"}},{\"@type\":\"Question\",\"name\":\"Do I need a transformer for a 12V waterproof LED strip?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Yes, a 12V strip is never connected directly to the mains: you need a transformer or driver that steps down the voltage. This unit must remain accessible, ventilated and protected from water. A strip designed for 230V does without it, but requires a fixed, careful installation.\"}}]}]}\u003c\/script\u003e","products":[],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0677\/8598\/2228\/collections\/designix-entete-rubans-led-etanches-12v-v1.jpg?v=1792690900","url":"https:\/\/designix-lighting.com\/collections\/12v-waterproof-led-strips.oembed","provider":"Designix","version":"1.0","type":"link"}