{"title":"12V G4 LED bulbs","description":"\u003cp\u003eCheck three things before buying a G4 LED bulb: the 12 V actually delivered by the fitting's transformer, the size of the bulb body in its housing, and the colour temperature already used in the room. The two-pin base is standard; everything else is chosen according to use and available space.\u003c\/p\u003e\n\n\u003ch2 id=\"reconnaitre\"\u003eWhat is a 12V G4 LED bulb and how do you recognise it?\u003c\/h2\u003e\n\u003cp\u003eA G4 bulb is recognisable by its two thin pins set into a small holder, with no screw thread or bayonet. It only works at 12 V, behind the transformer housed in the fitting or in the ceiling void. Before ordering, remove the old bulb and compare it side by side with the new one.\u003c\/p\u003e\n\n\u003ch3\u003eTwo thin pins, no screw thread\u003c\/h3\u003e\n\u003cp\u003eThe G4 base is not screwed in: the two pins push into the holder, like a plug into a socket. The pin spacing is standardised, but their length and the shape of the body are not. This freedom explains why one G4 bulb fits a spotlight while another jams in the one next to it. Also check the orientation of the holder: on some fittings, the bulb sits at an angle.\u003c\/p\u003e\n\n\u003ch3\u003eWhat changes compared with a G4 halogen\u003c\/h3\u003e\n\u003cp\u003eThe fitting, the holder and the transformer stay in place; only the bulb changes. An LED gives off less heat, which matters in a closed cabinet or under a display case, and it uses less power for comparable brightness. The existing transformer therefore runs at a lower load, a point to check before replacing everything. To see where the G4 sits among other bases, compare with \u003ca href=\"https:\/\/designix.fr\/collections\/ampoules\"\u003ethe catalogue of bulbs by base\u003c\/a\u003e, then return to \u003ca href=\"\/collections\/ampoules-led-12v\"\u003ethe low-voltage range as a whole\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2 id=\"ou-installer\"\u003eWhere should you install a 12V G4 bulb in the home?\u003c\/h2\u003e\n\u003cp\u003eThe G4 is used in fittings where the light point must stay small and precise: recessed spotlights, under-cabinet lighting, compact wall lights, display cases, terrace fittings. It is chosen to highlight a worktop or an object, not to light a whole room. The constraint is not the base but the space around the holder and the fitting's sealing.\u003c\/p\u003e\n\n\u003ch3\u003eDetail lighting: worktop, cabinet, display case\u003c\/h3\u003e\n\u003cp\u003eUnder a kitchen cabinet, a line of small light points avoids the shadow cast by your hand on the chopping board. In a display case, a bulb placed close to the object deepens the relief and brings out the material. A bedside or hallway wall light plays the same role more discreetly. In all three cases, LED is preferable to halogen: less heat in a closed volume. For the general ambience of a living room, start instead with \u003ca href=\"\/collections\/ampoules-pour-salon\"\u003eliving room bulbs\u003c\/a\u003e and keep the G4 for accent lighting.\u003c\/p\u003e\n\n\u003ch3\u003eWet rooms and outdoors: the protection rating comes first\u003c\/h3\u003e\n\u003cp\u003eIn a bathroom, near a shower, or on a terrace, it is the fitting's ingress protection rating that decides, not the bulb's. An open spotlight in a downpour lets water in even with a waterproof bulb. Look at the IP number marked on the fitting, and change the model if you cannot find it. The next step is \u003ca href=\"\/collections\/ampoules-d-exterieur-led\"\u003eoutdoor bulbs\u003c\/a\u003e for sheltered points, and \u003ca href=\"\/collections\/luminaire\"\u003eall our light fittings\u003c\/a\u003e if the holder itself needs replacing.\u003c\/p\u003e\n\n\u003ch2 id=\"temperature\"\u003eWhich colour temperature should you choose: cool white, neutral white or warm white?\u003c\/h2\u003e\n\u003cp\u003eWarm white, around 2700 to 3000 K, suits living rooms, bedrooms and dining areas. Neutral white, around 4000 K, lights worktops and bathrooms. Cool white, above 5000 K, gives a crisp result for display cases, workshops and outdoor areas. The choice is made by use, never by taste alone, and a single room keeps a single shade.\u003c\/p\u003e\n\n\u003ch3\u003eCool white: display cases, workshops, outdoor areas\u003c\/h3\u003e\n\u003cp\u003eAbove 5000 K, the light leans towards blue and brings out contrasts: useful for reading a label, sorting parts or lighting a driveway. In a living room, the same shade hardens faces and ages woodwork. A \u003ca href=\"\/collections\/ampoules-3000k\"\u003ebulb with a 3000 K rendering\u003c\/a\u003e remains the safest compromise when you hesitate between two adjoining rooms.\u003c\/p\u003e\n\n\u003ch3\u003eWarm white at 2700 K and 3000 K\u003c\/h3\u003e\n\u003cp\u003e2700 K gives a golden white, close to the incandescent bulb, ideal above a table in the evening. 3000 K adds a little crispness without turning yellow, handy in an open kitchen. If you mix the two in the same room, the difference shows on a white wall. Set the whole room to \u003ca href=\"\/collections\/ampoules-2700k\"\u003ethe 2700 K shade\u003c\/a\u003e or to a single nearby value.\u003c\/p\u003e\n\n\u003ctable\u003e\n\u003ccaption\u003eCool white, neutral white, warm white: the shade reference\u003c\/caption\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eColour temperature\u003c\/th\u003e\n\u003cth\u003eImpression\u003c\/th\u003e\n\u003cth\u003eCommon use\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e2700 K\u003c\/td\u003e\n\u003ctd\u003eVery warm white, golden\u003c\/td\u003e\n\u003ctd\u003eLiving room, bedroom, dining area\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e3000 K\u003c\/td\u003e\n\u003ctd\u003eWarm white, comfortable\u003c\/td\u003e\n\u003ctd\u003eKitchen, hallway, dining room\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e4000 K\u003c\/td\u003e\n\u003ctd\u003eNeutral white, crisp\u003c\/td\u003e\n\u003ctd\u003eBathroom, worktop, office\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e6000 K\u003c\/td\u003e\n\u003ctd\u003eCool white, very crisp\u003c\/td\u003e\n\u003ctd\u003eDisplay case, workshop, outdoor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2 id=\"puissance\"\u003eWhich power should you choose between a 12V G4 LED bulb of 5W, 10W or 20W?\u003c\/h2\u003e\n\u003cp\u003eThe wattage marked on a G4 LED bulb serves as a reference for replacing a halogen: for comparable brightness, LED uses less, so a lower figure is often enough. Compare above all the luminous flux in lumens, and check that the existing transformer handles the total load of the bulbs connected to it. Wattage alone does not tell you how much light is produced.\u003c\/p\u003e\n\n\u003ch3\u003e5W, 10W, 20W, 50W: read wattage as a reference\u003c\/h3\u003e\n\u003cp\u003eA higher figure announces a brighter bulb, not a better one. For cabinet lighting, a discreet bulb is enough; in a display case or a spotlight high up, you need more output. Look at the lumens line on the data sheet; that is what describes the result. A very low stated flux with a high wattage points to a poorly filled data sheet: in that case rely on wattage alone. For dimmable light points, see also \u003ca href=\"\/collections\/ampoules-led-a-variateur\"\u003edimmer-compatible bulbs\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eThe transformer, the real limit on total power\u003c\/h3\u003e\n\u003cp\u003eA 12 V transformer has a load range: too many bulbs on it and it heats up or cuts out; too few and some LED bulbs flicker or stay dim. Add up the power of all the points connected to the same transformer, not just the one you are replacing. If you replace halogens with LEDs, the load drops sharply, hence the malfunctions. The full family is on \u003ca href=\"\/collections\/ampoules-12v\"\u003e12 V bulbs for fittings with a transformer\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2 id=\"dimensions\"\u003eWhat are the dimensions of a G4 LED bulb?\u003c\/h2\u003e\n\u003cp\u003eThe G4 base fixes the spacing of the two pins, not the size of the bulb: the diameter and height of the body vary from one model to another, and some bulbs have differently shaped pins. The only reliable method is to measure the fitting's cavity before ordering. A bulb that is too tall prevents the protective glass from being refitted.\u003c\/p\u003e\n\n\u003ch3\u003eMeasuring the fitting's cavity\u003c\/h3\u003e\n\u003cp\u003eRemove the old bulb and measure with a ruler: the clear diameter of the housing, the height between the base of the holder and the glass, and the depth of the holder itself. Also note the pin spacing, which must match that of the holder. A margin of a few millimetres avoids forcing it when refitting. This measurement applies to a recessed spotlight as well as to a wall light.\u003c\/p\u003e\n\n\u003ch3\u003eRecognising the pin shape before ordering\u003c\/h3\u003e\n\u003cp\u003eSome bulbs have straight pins, others slightly bent or longer. In a slightly deep holder, a short pin does not make contact. Compare the photo of the bulb with your old one, pins facing you. If doubt remains, \u003ca href=\"\/collections\/ampoules-led-gu5\"\u003eGU5 LED bulbs for ceiling spotlights\u003c\/a\u003e and \u003ca href=\"\/collections\/ampoules-led-1\"\u003eall LED bulbs\u003c\/a\u003e let you compare the families before deciding.\u003c\/p\u003e\n\n\u003ch2 id=\"resistance\"\u003eWhat resistance for an LED at 12V?\u003c\/h2\u003e\n\u003cp\u003eNo resistor is needed when the G4 bulb is powered by a transformer or a 12 V driver intended for lighting. Resistance only concerns the assembly of bare LED components on a board. In a fitting, you check instead that the transformer really delivers 12 V and accepts the connected load. A tired transformer is replaced, not bypassed.\u003c\/p\u003e\n\n\u003ch3\u003eThe transformer does the regulation\u003c\/h3\u003e\n\u003cp\u003eA lighting transformer or LED driver converts the 230 V mains supply to 12 V and limits the current. It is what protects the bulb, not a component added inside the fitting. An old halogen transformer, sometimes heavy and noisy, accepts LEDs unevenly depending on its age and technology. When you change a bulb, note the transformer reference: it will save you a second trip. Switching to mains is described under \u003ca href=\"\/collections\/ampoules-led-220v\"\u003emoving to a 220 V bulb\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eFlickering or dim bulb: the two common causes\u003c\/h3\u003e\n\u003cp\u003eFirst cause, too low a load: only a few LEDs on a transformer intended for halogens, and the bulb flickers. Second cause, a transformer at the end of its life or of an incompatible model. Test an identical bulb on another point of the same circuit to isolate the culprit. If it works elsewhere, the problem comes from the transformer or the holder, not the bulb.\u003c\/p\u003e\n\n\u003ch2 id=\"installer\"\u003eHow do you install and maintain a 12V G4 bulb?\u003c\/h2\u003e\n\u003cp\u003eSwitch off the power at the consumer unit before touching the fitting, then remove the bulb by pulling it straight out by the body, never by the pins. Replacement is like for like: same voltage, same base, same size. A dry cloth is enough for cleaning, with no product on the holder. The protective glass goes back on before switching the power back on.\u003c\/p\u003e\n\n\u003ch3\u003eRemoving the bulb without bending the pins\u003c\/h3\u003e\n\u003cp\u003eThin pins bend easily. Hold the bulb between two fingers, pull along the axis of the holder, with no sideways movement. If it resists, check that a glass or a clip is not holding it. When refitting, present the two pins along the axis, without forcing: a holder can crack. On a \u003ca href=\"\/collections\/ampoules-en-verre\"\u003eglass bulb\u003c\/a\u003e, hold the body by the wide part, never by the edge of the glass.\u003c\/p\u003e\n\n\u003ch3\u003eChanging shade or power: the checks\u003c\/h3\u003e\n\u003cp\u003eWhen you change the shade of a light point, go round the other bulbs in the room to avoid a visible mix on light-coloured walls. When you increase the power, recheck the transformer load and the space available under the glass. On an old fitting, take the opportunity of changing the bulb to look at the condition of the holder. The rest of the range is in \u003ca href=\"\/collections\/luminaire\"\u003ethe home's light fittings\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2 id=\"culots\"\u003eG4, GU5.3, GU10 or E27: which base for which fitting?\u003c\/h2\u003e\n\u003cp\u003eG4 and GU5.3 are pin bases for 12 V fittings; GU10 is also a pin base but on 230 V mains; E27 and E14 are screw bases on mains. A ceiling light, a chandelier or a wall light rarely takes a G4: these fittings most often use a screw base or a built-in LED that cannot be replaced. The bulb's base must match that of the holder.\u003c\/p\u003e\n\n\u003ch3\u003eG4 and GU5.3, the same low-voltage family\u003c\/h3\u003e\n\u003cp\u003eBoth connect behind a transformer, but the GU5.3 pins are thicker and further apart: the bulbs are not interchangeable. GU5.3 is used in ceiling recessed spotlights, G4 in smaller volumes. An LED wall light only accepts a G4 if the manufacturer states a G4 holder and a 12 V transformer; otherwise the bulb is built in. A cuttable LED strip, for its part, is cut only at the marked points, otherwise a section stops lighting.\u003c\/p\u003e\n\n\u003ch3\u003eCeiling light, chandelier, wall light: rarely a G4\u003c\/h3\u003e\n\u003cp\u003eBefore ordering, read the base on the fitting's data sheet rather than on the old bulb, which is sometimes worn away. A living room chandelier or a hallway wall light is wired at 230 V. For these models, go for a screw base: \u003ca href=\"\/collections\/ampoules-culot-e27\"\u003elarge E27 screw base\u003c\/a\u003e for ceiling lights, \u003ca href=\"\/collections\/ampoules-e14\"\u003eE14 bulbs for wall lights\u003c\/a\u003e and \u003ca href=\"\/collections\/ampoules-led-g9\"\u003eG9 base for small chandeliers\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ctable\u003e\n\u003ccaption\u003eBase comparison: which one fits which fitting\u003c\/caption\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003cth\u003eFixing\u003c\/th\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003cth\u003eTypical fittings\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eG4\u003c\/td\u003e\n\u003ctd\u003eTwo thin pins\u003c\/td\u003e\n\u003ctd\u003e12 V via transformer\u003c\/td\u003e\n\u003ctd\u003eRecessed spotlights, cabinet lighting, small wall lights\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGU5.3\u003c\/td\u003e\n\u003ctd\u003eTwo thicker pins\u003c\/td\u003e\n\u003ctd\u003e12 V via transformer\u003c\/td\u003e\n\u003ctd\u003eRecessed ceiling spotlights\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGU10\u003c\/td\u003e\n\u003ctd\u003eTwo bayonet pins\u003c\/td\u003e\n\u003ctd\u003e230 V mains\u003c\/td\u003e\n\u003ctd\u003eAdjustable spotlights and tracks\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eG9\u003c\/td\u003e\n\u003ctd\u003eTwo pins, flat bulb\u003c\/td\u003e\n\u003ctd\u003e230 V mains\u003c\/td\u003e\n\u003ctd\u003eChandeliers and compact wall lights\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eE14\u003c\/td\u003e\n\u003ctd\u003eSmall screw thread\u003c\/td\u003e\n\u003ctd\u003e230 V mains\u003c\/td\u003e\n\u003ctd\u003eSmall chandeliers and wall lights\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eE27\u003c\/td\u003e\n\u003ctd\u003eLarge screw thread\u003c\/td\u003e\n\u003ctd\u003e230 V mains\u003c\/td\u003e\n\u003ctd\u003eCeiling lights, chandeliers, floor lamps\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cp\u003eNot sure which model to order? Compare your old bulb with the two references in the collection, pins facing you and ruler in hand, before confirming the basket. Secure payment, tracked delivery, returns and Designix customer service are there to help if the size does not match.\u003c\/p\u003e\n\n\u003ch2 id=\"faq\"\u003eFrequently asked questions about 12V G4 LED bulbs\u003c\/h2\u003e\n\n\u003cdetails\u003e\n\u003csummary\u003eWhat are the dimensions of a G4 LED bulb?\u003c\/summary\u003e\n\u003cp\u003eThe name of the G4 base refers to the spacing of the two pins, but the size of the body is not standardised: diameter and height change from one model to another. Before ordering, measure the fitting's cavity, the height available under the glass and the shape of the holder's pins.\u003c\/p\u003e\n\u003c\/details\u003e\n\n\u003cdetails\u003e\n\u003csummary\u003eWhat resistance for an LED at 12V?\u003c\/summary\u003e\n\u003cp\u003eNo resistor is to be added inside a fitting: the G4 LED bulb is powered by a transformer or a 12 V driver that already regulates the current. A resistor is only used for assembling bare LED components. Check instead that the transformer delivers 12 V and handles the connected load.\u003c\/p\u003e\n\u003c\/details\u003e\n\n\u003cdetails\u003e\n\u003csummary\u003eCan a G4 bulb be put in a ceiling light or a chandelier?\u003c\/summary\u003e\n\u003cp\u003eOnly if the fitting has a G4 holder and a 12 V transformer. Most ceiling lights and chandeliers are wired at 230 V with an E27 or E14 screw base, and many recent models have a built-in LED that cannot be replaced. Check the base on the data sheet before buying.\u003c\/p\u003e\n\u003c\/details\u003e\n\n\u003cdetails\u003e\n\u003csummary\u003eWhat is the difference between a 12V G4 LED bulb and a 220V bulb?\u003c\/summary\u003e\n\u003cp\u003eA 12V G4 bulb connects behind a low-voltage transformer, whereas a 220V bulb connects directly to the mains, with a screw or bayonet base. A G4 bulb cannot be fitted to a GU10, E27 or E14 holder: the base must match the fitting in place.\u003c\/p\u003e\n\u003c\/details\u003e\n\n\u003cdetails\u003e\n\u003csummary\u003eMy G4 LED bulb does not light up or flickers: what should I check?\u003c\/summary\u003e\n\u003cp\u003eCheck the power at the consumer unit, then the condition of the pins and that they are properly inserted in the holder. If the bulb flickers or stays dim, the transformer is often the cause: too low a load, an incompatible model or a transformer at the end of its life. Test an identical bulb on another point of the circuit.\u003c\/p\u003e\n\u003c\/details\u003e\n\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"CollectionPage\",\"name\":\"12V G4 LED bulbs: choosing your low-voltage two-pin bulb\",\"description\":\"G4 base, 12 V, cool white or warm white: the guide to choosing your G4 LED bulb according to the fitting, the room and the transformer already in place.\",\"url\":\"https:\/\/designix.fr\/collections\/ampoules-led-12v-g4\",\"isPartOf\":{\"@type\":\"WebSite\",\"name\":\"Designix\",\"url\":\"https:\/\/designix.fr\"},\"speakable\":{\"@type\":\"SpeakableSpecification\",\"cssSelector\":[\"h1\",\"h2\"]}},{\"@type\":\"BreadcrumbList\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/designix.fr\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Lighting\",\"item\":\"https:\/\/designix.fr\/collections\/luminaire\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Bulbs\",\"item\":\"https:\/\/designix.fr\/collections\/ampoules\"},{\"@type\":\"ListItem\",\"position\":4,\"name\":\"12V G4 LED bulbs: choosing your low-voltage two-pin bulb\",\"item\":\"https:\/\/designix.fr\/collections\/ampoules-led-12v-g4\"}]},{\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"What are the dimensions of a G4 LED bulb?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"The name of the G4 base refers to the spacing of the two pins, but the size of the bulb body is not standardised: diameter and height change from one model to another. Before ordering, measure the fitting's cavity, the height available under the glass and the shape of the holder's pins.\"}},{\"@type\":\"Question\",\"name\":\"What resistance for an LED at 12V?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"No resistor is to be added inside a fitting: the G4 LED bulb is powered by a transformer or a 12 V driver that already regulates the current. A resistor is only used for assembling bare LED components. Check instead that the transformer delivers 12 V and handles the load.\"}},{\"@type\":\"Question\",\"name\":\"Can a G4 bulb be put in a ceiling light or a chandelier?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Only if the fitting has a G4 holder and a 12 V transformer. Most ceiling lights and chandeliers are wired at 230 V with an E27 or E14 screw base, and many recent models have a built-in LED that cannot be replaced. Check the base before buying.\"}},{\"@type\":\"Question\",\"name\":\"How does a cuttable LED strip work?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"The strip has cut marks: cut only at these marks, otherwise some of the LEDs stop lighting. The sections are then connected with a suitable connector or power cable. Like the G4 bulb, the strip runs on low voltage and depends on a transformer.\"}},{\"@type\":\"Question\",\"name\":\"Can an LED wall light take a G4 bulb?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"It depends on the model: a wall light with a G4 holder and a 12 V transformer accepts these bulbs, an integrated-LED wall light does not. For a living room, check above all the base stated on the data sheet, the ingress protection rating if the wall light is near water, and the space available around the holder.\"}},{\"@type\":\"Question\",\"name\":\"What is the difference between a 12V G4 LED bulb and a 220V bulb?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"A 12V G4 bulb connects behind a low-voltage transformer, whereas a 220V bulb connects directly to the mains, with a screw or bayonet base. A G4 bulb cannot be fitted to a GU10, E27 or E14 holder: the base must match the fitting in place.\"}},{\"@type\":\"Question\",\"name\":\"My G4 LED bulb does not light up or flickers: what should I check?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"First check the power at the consumer unit, then the condition of the pins and that they are properly inserted in the holder. If the bulb flickers or stays dim, the transformer is often the cause: too low a load, an incompatible model or a transformer at the end of its life. Test an identical bulb on another point.\"}}]}]}\u003c\/script\u003e","products":[],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0677\/8598\/2228\/collections\/designix-entete-ampoules-led-12v-g4-v1.jpg?v=1792910374","url":"https:\/\/designix-lighting.com\/collections\/12v-g4-led-bulbs.oembed","provider":"Designix","version":"1.0","type":"link"}